GE ZIC360NXRH - Manual (Page 4)

monogram.com
95
B
u
ilt
-i
n
a
ll
-r
e
fr
ig
e
ra
to
rs
an
d
al
l-
fre
e
ze
rs
Fu
lly i
n
te
g
ra
te
d
re
fr
ig
era
to
rs
/
w
ine
r
ese
rv
e
B
u
il
t-
in
si
d
e
-b
y-
si
d
e
re
fr
ig
e
ra
to
rs
Fre
e
-s
tan
d
in
g
re
fr
ig
era
to
rs
B
uil
t-
in
b
ot
to
m
-f
re
e
ze
r
re
fr
ig
e
ra
to
rs
1/4" framed panel dimensions 3/4" overlay panel dimensions
If you choose to install framed
panels, they must be cut to the
dimensions shown. The panels
will slide into the frame on the
door, drawer and grille.
If the custom panel is less than
1/4" thick, and it fits loosely in the
door frame, it can be backed up
with a piece of filler material or
foam tape to improve the fit.
Important note: Maximum
weight for fresh-food panel
is 58 pounds, 28 pounds for
freezer drawer panel and 11
pounds for the grille panel.
729Dia84
1/4"
Panel
Door/Drawer
5/16"
Trim
Reveal
For a more custom
appearance, overlay
panels may be installed
on trimmed models. The
overlay panel must be secured
to a 1/4"-thick backer panel
which slides into the trim. A
spacer panel 0.10" thick must
be placed between the overlay
and backer panel.
729Dia42
Overlay
Panel
1/4"
Backer
Panel
Door/Drawer
.10 Inch
Spacer
Fresh Food
Panel
729Dia89
Freezer Drawer
Panel
D
C
A
B
Grille Panel
Framed panel dimensions (in inches)
A (width) B (grille ht.) C (FF ht.) D (FZ ht.)
1/4" framed panel 33-7/8 8-7/8 46-1/16 21-7/8
3/4" overlay panel dimensions (in inches)
A (width) B (grille ht.) C (FF ht.) D (FZ ht.)
1/4" backer panel 33-7/8 8-7/8 46-1/16 21-7/8
.10" spacer panel 32-1/2 7-5/8 44-11/16 20-1/2
3/4" overlay panel 34-1/8 9 46-5/16 22
Center each panel
over the other.
Assemble the
panels with glue
and screws.
Screws must be
countersunk into
the backer panel.
729Dia85
A
B Grille Panel
.250" + .10" + .750" =
1.100" total panel thickness
Note: Left-to-right offset is not always equal to
top-to-bottom offset.
ZUG2 grille panel dimensions
The ZUG2 unified grille panel kit will accept a framed or
overlay grille panel.
• Assemble the overlay panel in the same manner
as the door and drawer panels.
Framed panel dimensions
A (width) B (height)
1/4" framed panel 69-7/8" 8-7/8"
Overlay panel dimensions
A (width) B (height)
1/4" backer panel 69-7/8" 8-7/8"
.10" spacer panel 68-1/2" 7-5/8"
3/4" overlay panel 70-1/8" 9"
Advance planning for built-in custom bottom-freezer refrigerators
194Dia65
Spacer Panel
Overlay Panel
Backer Panel
Important: Grille panel maximum total weight is 25 lbs.