Alto-Shaam COMPITHERM 2020ESG - Manual (Page 10)

COMBITOUCH TM ESG SERIES • GAS INSTALLATION MANUAL • 8.
10 •10
ES
G
21-11/16"
(550mm)
5-3/16"
(131mm)
42-1/16" (1068mm)
40-1/8"
(1018mm)
37" (939mm)
34-5/16"
(871mm)
Water Drain
(Bottom)
5" (125mm)
5-9/16" (140mm)
40-1/8" (1019mm)
33-7/8" (860mm)
44-15/16" (1141mm)
25"
(635mm)
7-1/2"
(191mm)
6-1/4" (159mm)
B
C
D
2-15/16"
(74mm)
2" (50mm)
47-5/16" (1201mm)
2-3/8" (60mm)
10-9/16
"
(267mm)
19-3/8" (492mm)
5-11/16" (144mm)
4-1/2" (114mm)
A = UNTREATED WATER
B = TREATED WATER
C = ELECTRICAL
D = GAS
A
Steam
Vent
(Top)
58-3/16" (1478mm)
15-3/16"
(385mm)
Water Drain
(Back Side)
DIMENSIONS: H x W x D
EXTERIOR:
44-15/16” x 42-1/16” x 37” (1141mm x 1068mm x 939mm)
EXTERIOR WITH RECESSED DOOR:
44-15/16” x 46-1/16” x 37” (1141mm x 1170mm x 939mm)
INTERIOR:
27-3/8” x 17-3/8” x 26-13/16” (695mm x 440mm x 680mm)
GAS REQUIREMENTS ( TYPE MUST BE SPECIFIED ON ORDER ) INSTALLATION REQUIREMENTS
CONNECTED ENERGY LOAD: 68,000 Btu / hr Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow preventer.
Alternate burner orifice is required for installation sites at
elevations of 2,000 feet (610m) above sea level.
HOOK-UP: 3/4” NPT
MINIMUM CONNECTED PRESSURE: 5.5” W.C. (Natural Gas)
9” W.C. (Propane)
MAXIMUM CONNECTED PRESSURE: 14” W.C.
ELECTRICAL (DEDICATED CIRCUIT REQUIRED) 10●10ESG 10●10ESG / sk
VOLTAGE PHASE CYCLE/HZ AWG AMPS kW AMPS kW
110 – 120 1 50/60 NEMA 5-20P, 20A, 125V Plug, AWG 12 9.2 1.05 13.7 1.57
OTHER VOLTAGES AVAILABLE:
Range 200 – 415V – 1 or 3 ph, 50 or 60 Hz
WEIGHT CAPACITY
NET 300 lb est (136 kg) FULL-SIZE PANS: 20” x 12” x 2-1/2” Ten (10) Nine (9)
SHIP 457 lb (207 kg) GN 1/1: 530 x 325 x 65mm Ten (10) Nine (9)
CRATE DIMENSIONS: (L x W x H) EST HALF-SIZE SHEET PANS:* 18” x 13” x 1” Ten (10) Nine (9)
45” x 53” x 48” ON WIRE SHELVES ONLY
(1143 x 1346 x 1219mm)
120 lb (54 kg) MAXIMUM
VOLUME MAXIMUM: 75 quarts (95 liters)
*ADDITIONAL WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET: 3/4” NPT*
ONE (1) UNTREATED WATER INLET: 3/4” NPT*
LINE PRESSURE: 30 to 90 psi 2.8 to 6.2 bar
WATER DRAIN: 1-1/2” CONNECTION WITH A 2” MINIMUM
AIR GAP INSTALLED AS CLOSE TO THE OVEN AS POSSIBLE
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM’S MINIMUM
WATER QUALITY STANDARDS WILL VOID THIS WARRANTY.
It is the responsibility of the purchaser to ensure that incoming water supply is
compliant with the specifi cations listed through adequate treatment measures.
Installation of the CombiGuard
TM Water Filtration System is recommended, but
this system may not address all water quality issues present.
CLEARANCE REQUIREMENTS Contaminant
Free Chlorine
Hardness
Chloride
pH
Alkalinity
Silica
Total Dissolved Solids (tds)
Inlet Water Requirements ( untreated water )
Less than 0.1 ppm (mg/L)
Less than 3 gpg (52 ppm)
Less than 30 ppm (mg/L)
7.0 to 8.5
Less than 50 ppm (mg/L)
Less than 12 ppm (mg/L)
Less than 60 ppm
LEFT 6” (152mm) RECOMMENDED SERVICE ACCESS: 18” (457mm)
20” (508mm) FROM HEAT PRODUCING EQUIPMENT
RIGHT 4” (102mm) TOP: 20” (508mm) FOR AIR MOVEMENT
BACK 4” (102mm) BOTTOM: 5-1/8” (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4” (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE
* Can manifold off of
one 3/4” line.