Kenwood KDC-BT60U - Manual (Page 7)

English |
7
Before Using
Exit of the Demonstration Mode
Turn off the demonstration mode when you use it
for the first time after installation.
1
Press the [VOL] knob to quit the demonstration
mode when the messages “To cancel Demo
press the volume knob” are displayed (approx. 15
seconds).
2
Turn the [VOL] knob to select “YES” and press the
[VOL] knob.
⁄
• Demonstration mode can also be cancelled in “DEMO
Mode” of Menu List mode. Refer to <Demonstration mode
Setting> (page 35) .
Common Operation
Power and source select
Turns the power ON by pressing the [SRC]
button.
When the power is ON, select a source.
• SRC Select mode 1: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
• SRC Select mode 2: Pressing the [SRC] button
each time switches between sources.
Tuner (“TUNER”)
➜ Bluetooth Audio (“BT
AUDIO”) (KDC-BT60U only) ➜ USB (“USB”)
or iPod (“iPod”) ➜ Auxiliary input (“AUX”) ➜
Standby (“STANDBY”) ➜ Tuner...
Keeping pressing the [SRC] button for at least 1
second turns the power OFF.
⁄
• The SRC Select mode can be set in “SRC Select” of <Initial
Settings> (page 34) .
• Auxiliary input source is initially set to “OFF”. Set “Built in
AUX” described in <Initial Settings> (page 34) to “ON”.
• When an optional accessory is connected, the source name
for each device appears.
• When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
• This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle’s battery. The time until full power OFF can be set in
“Power OFF Wait” of
<Initial Settings> (page 34) .
Volume
Turning the [VOL] knob adjusts the sound
volume.
Menu List Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
1
Select the source
Press the [SRC] button. Turn the [VOL] knob
and press it when the desired item is displayed.
Function items vary from source to source. For a list
of the function items. Refer to
<Menu List> (page 58) .
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
Enter Menu List mode
Press the [MENU] button.
3
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired setup item
is selected.
✍ Press the [MENU] button to return to the
previous item.
Operation example:
Music
PlayLists
My Best 25
…
Artists
Albums
…
Play Mode
…
[VOL] [MENU]
[VOL] [MENU]
1 1
2
2
3
4
3 1 3
2 4
1 sec.
In this manual, the above selection is indicated as
Select “Music”
> “Playlists” > “My Best 25”.
4
Make a setting
• When the “
PUSH ” icon is displayed (at the
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “ PUSH ” icon is not displayed
Press the [ 4] or [¢] button to select a
setting value.
5
Exit Menu List mode
Press the [MENU] button for at least 1 second to
return to the first hierarchy. Press the [MENU]
button in the first hierarchy to exit the Menu
List mode.
⁄
• You cannot set the item with the “ ” icon displayed.
General operation