Videotec NXPTZT User Manual
Nxptz, nxptzt
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- ENGLISH
- 1 About this manual
- 2 Notes on copyright and information on trademarks
- 3 Safety rules
- 4 Identification
- 5 Versions
- 6 Preparing the product for use
- 7 Assembling and installing
- 7.1 Installation
- 7.2 Hardware configuration
- 7.2.1 Opening the configuration door
- 7.2.2 Configuration of the dip-switches
- 7.2.3 Setting the configuration check mode
- 7.2.4 Baud rate configuration
- 7.2.5 Setting of the serial communication lines
- 7.2.6 Serial line terminations
- 7.2.7 Protocol configuration
- 7.2.8 Address configuration
- 7.2.9 Configuration of the version with IP board
- 7.2.10 Closing the configuration door
- 8 Switching on
- 9 Configuration
- 9.1 OSM interface (On Screen Menu)
- 9.1.1 Using the OSM
- 9.1.2 Configuration via OSM
- 9.1.3 Main menu
- 9.1.4 Language
- 9.1.5 Camera menu
- 9.1.5.1 Zone Titling Menu
- 9.1.5.2 Zone Titling Menu (Edit Area)
- 9.1.5.3 Masking Menu
- 9.1.5.4 Masking Menu (Edit Masks)
- 9.1.5.5 How to create a new mask
- 9.1.5.6 How to modify a mask
- 9.1.5.7 Advanced Setting Menu
- 9.1.5.8 Advanced Setting Menu (Zoom)
- 9.1.5.9 Advanced Setting Menu (Focus)
- 9.1.5.10 Advanced Setting Menu (Exposure)
- 9.1.5.11 Advanced Setting Menu (Infrared)
- 9.1.5.12 Advanced Setting Menu (White Balance)
- 9.1.5.13 Advanced Setting Menu (Other)
- 9.1.6 Movement Menu
- 9.1.7 Display Menu
- 9.1.8 Options Menu
- 9.1.9 Washer Menu
- 9.1.10 Default Menu
- 9.1.11 Info Menu
- 9.1.12 Thermal Camera Menu
- 9.1.12.1 Flat Field Correction Menu
- 9.1.12.2 Flat Field Correction Menu (Gain Switch Values)
- 9.1.12.3 Video Setup Menu
- 9.1.12.4 Gain Control Menu
- 9.1.12.5 ROI Setup Menu
- 9.1.12.6 Thermal Analysis Menu
- 9.1.12.7 Thermal Analysis Menu (Spot Meter)
- 9.1.12.8 Thermal Analysis Menu (Isotherm)
- 9.1.12.9 Status Menu
- 9.2 Sofware interface
- 9.3 Web interface
- 9.3.1 Home
- 9.3.2 User Controls
- 9.3.3 Device Parameters
- 9.3.4 Device Statistics
- 9.3.5 Network Configuration
- 9.3.6 User Configuration
- 9.3.7 Movement Parameters
- 9.3.8 Preset Parameters
- 9.3.9 Preset Parameters (Advanced)
- 9.3.10 Digital I/O
- 9.3.11 Washer
- 9.3.12 Camera Parameters
- 9.3.13 Tools
- 9.3.14 Factory Default
- 9.1 OSM interface (On Screen Menu)
- 10 Accessories
- 11 Instructions for normal operation
- 11.1 Visualizing the state of the pan & tilt
- 11.2 Saving the current position (Preset)
- 11.3 Recalling a position (Scan)
- 11.4 Enabling the patrol (Patrol)
- 11.5 Enabling Autopan Function
- 11.6 Recalling a pattern (Tour)
- 11.7 Recalling the Home position
- 11.8 Enabling the wiper (Wiper)
- 11.9 Enabling the washer (Washer)
- 11.10 Reboot the device
- 11.11 Manual correction of a preset focusing
- 11.12 Web interface
- 11.13 Special controls
- 12 Maintaining and cleaning
- 13 Disposal of waste materials
- 14 Troubleshooting
- 15 Technical data
- 16 Technical drawings