Videotec SM164B - Manual (Page 66)

Page 26 MNVCSM84A_0408
[COAX TRANSM. / AUX LINE 2.7]
[----------------------------]
[ 1.Coax Transmission: NO ]
[ 2.Aux Line: TELEM.MACRO ]
[ 3.Aux Baudrate: 384OO ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[SEQ.End ]
Coax and Aux Line Transmission Submenu
The matrix is able to transmit telemetry commands via coaxial cable and to
control both telemetry receivers and video multiplexers using the Aux line.
Press
!
to enable/disable transmission via coaxial cable.
Press
"
to select the protocol for the Aux line.
Press
#
to choose the baud rate.
Protocol Pelco D/Eneo is used in a wide range of domes and receivers. These
objects don't move at the same speed and it can be useful to change speed
factors when speeds are too high or movement is not smooth enough.
It is recommended to try the four available speed factors and then choose the
one that allows better movements.
Please note: to be able to use transmission via coaxial cable or along the Aux
line, it is necessary to set the MACRO protocol towards the keyboards! Any
other protocol will not allow the Coax and Aux lines to transmit the intended
messages.
[VIDEO 2.8]
[----------------------------]
[ ]
[ 1.System: PAL ]
[ 2.Interlaced: YES ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[SEQ.End ]
Video Submenu
Press
!
to change the type of video code system: Pal or NTSC.
Press
"
to change the type of output video signal in On Screen Menu mode.
Interlaced setting: No, for greater text stability. However, for some types of
monitor (digital types in particular) the function may cause image compression
problems; in which case set interlaced to: Yes.
[CYCLE SEQUENCES 3]
[----------------------------]
[ 1. Day seq, Output 1 ]
[ 2. Day seq, Output 2 ]
[ 3. Day seq, Output 3 ]
[ 4. Day seq, Output 4 ]
[ 5.Night seq, Output 1 ]
[ 6.Night seq, Output 2 ]
[ 7.Night seq, Output 3 ]
[ 8.Night seq, Output 4 ]
[ ]
[SEQ.End ]
Cycle sequences submenu (night-time and daytime)
The cycle sequences submenu may be shown in different formats, depending
on whether night-time sequences have been enabled and on the number of
output videos the matrix has.
Night-time video sequences are only present if their use has been enabled. If
not a simplified menu is shown as in the next section.
Press
!
...
(
to proceed with switching sequence modification, or

to
return to the main menu. (See section 4.1.2)
[CYCLE SEQUENCES 3]
[----------------------------]
[ 1.Output 1 ]
[ 2.Output 2 ]
[ 3.Output 3 ]
[ 4.Output 4 ]
[ ]
[ ]
[ ]
[ ]
[ ]
[SEQ.End ]
Cycle sequences submenu (only daytime)
If the night-time sequences are not used (a single sequence is used for each
output for the complete 24-hour day, without differences for working days and
holidays) a simplified menu is shown.
Press
!
...
$
to select the desired sequence or

to return to the main
menu. (See section 4.1.2)
[OUTPUT 1 3.1]
[----------------------------]
[Step: Cam Time ]
[ > A: 1 2 ]
[ B: 2 2 Step: ]
[ C: 3 2 INC.Previous ]
[ D: 4 2 DEC.Next ]
[ ]
[---------------- ]
[1..16.Camera ]
[ENTER/CLEAR.Change Time ]
[SEQ.End ]
Sequence Modify submenu
Each cycle sequence consists of a max. of 16 steps, each of which is defined
by an input video to be viewed, and by the viewing time in seconds. The
screen shows only 4 steps at a time while the others can be requested by
pressing
8
and
9
.
The cursor > indicates the step being modified: press the desired camera
number, and increase/decrease the viewing time with

/

.
When sequence definition is complete, press

to confirm and return to the
previous menu.