Horner APG QX651 OCS User Manual
Page 7
MAN0797-03-EN
Specifications / Installation
_______________________________________________________________________________________________________________________________________________
9/16/2009 Page 7 of 7 ECN # 968
5
Additional References
6
Technical Support
WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES EMPLACEMENTS DE
CLASSE 1, DIVISION 2.
WARNING - The USB parts are for operational maintenance only. Do not leave permanently connected unless area is known to be non-hazardous.
WARNING – EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS
AVERTISSEMENT - RISQUE D'EXPLOSION - AFIN D'EVITER TOUT RISQUE D'EXPLOSION, S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX
AVANT DE CHANGER LA BATTERIE
WARNING - Battery May Explode If Mistreated. Do Not Recharge, Disassemble or Dispose Of In Fire
WARNING: Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, or service
this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe
bodily injury or loss of life.
For detailed installation and a handy checklist that covers panel box layout requirements and minimum clearances, refer the hardware manual of the QX Series (MAN0798).
(See the Additional References section in this document.)
•
All applicable codes and standards need to be followed in the installation of this product.
•
For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG or larger.
Adhere to the following safety precautions whenever any type of connection is made to the module.
•
Connect the green safety (earth) ground first before making any other connections.
•
When connecting to electric circuits or pulse-initiating equipment, open their related breakers. Do not make connections to live power lines.
•
Make connections to the module first; then connect to the circuit to be monitored.
•
Route power wires in a safe manner in accordance with good practice and local codes.
•
Wear proper personal protective equipment including safety glasses and insulated gloves when making connections to power circuits.
•
Ensure floor, hands and shoes are dry before making any connection to a power line.
•
Make sure the unit is turned OFF before making connection to terminals. Make sure all circuits are de-energized before making connections.
•
Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if defective.
The following information serves as a general listing of Horner controller products
and other references of interest and their corresponding manuals numbers. Visit
our website listed in the Technical Support section to obtain user documentation
and updates.
Note: This list is not intended for users to determine which products
are appropriate for their application; controller products differ in the
features that they support. If assistance is required, see the Technical
Support section in this document.
Controller
Manual Number
XLe/XLt Manual Series (e.g., HE-XExxx)
MAN0878-03
QX Series (e.g., HE-QXxxx)
MAN0798
NX Series (e.g., HE-NXxxx)
MAN0781
LX Series (e.g., LX-xxx; also covers
RCS116)
MAN0755
Color Touch OCS (e.g., OCSxxx)
MAN0465
OCS (Operator Control Station) (e.g.,
OCS1xx / 2xx; Graphic OCS250)
MAN0227
Remote Control Station (e.g., RCS2x0)
XL6e
MAN0883
QX351
MAN0892
MiniOCS (e.g., HE500OCSxxx,
HE500RCSxxx)
MAN0305
Other Useful References
CAN Networks
MAN0799
Cscape Programming and Reference
MAN0313
Wiring Accessories and Spare Parts
Manual
MAN0347
For assistance and manual updates, contact Technical Support at the following
locations:
North America:
Tel: 317-916-4274
Fax: 317-639-4279
Web: http://www.heapg.com
Email:
Europe:
Tel: +353-21-4321-266
Fax: +353-21-4321-826
Web: http://www.horner-apg.com
Email:
No part of this publication may be reproduced without the prior agreement and
written permission of Horner APG, Inc. Information in this document is subject to
change without notice.
Cscape, SmartStack, SmartStix and CsCAN are trademarks of Horner APG.
CompactFlash is a registered trademark of SanDisk Corporation.
Ethernet is a trademark of Xerox Corporation.