Document Outline

• Contents
• List of Figures
• List of Tables
• Preface
  • Product Documentation
  • Starting a Management Session
  • Safety Symbols Used in this Document
  • Where to Find Web-based Guides
  • Contacting Allied Telesis
    • Online Support
    • Email and Telephone Support
    • Warranty
    • Returning Products
    • Sales or Corporate Information
    • Management Software Updates
• Chapter 1
  • Overview
    • Introduction
    • Switch Descriptions
      • x610-24Ts Switch
      • x610-24Ts/X Switch
      • x610-48Ts Switch
      • x610-48Ts/X Switch
      • x610-24SPs/X Switch
      • x610-24Ts-POE+ Switch
      • x610-24Ts/X- POE+ Switch
      • x610-48Ts-POE+ Switch
      • x610-48Ts/X- POE+ Switch
    • 10/100/1000Base-T Ports
      • Connector Type
      • Speed
      • Duplex Mode
      • Maximum Distance
      • Cable Type
      • Auto-MDI/ MDI-X
      • Port Pinouts
    • SFP and SFP+ Transceiver Slots
    • Combo Ports
    • SD Card Slot
    • Port LEDs
      • 10/100/1000 Base-T LEDs
      • SFP and SFP+ LEDs
    • System STATUS LEDs
    • STACK LEDs
    • Secure Digital (SD) LED
    • Terminal Port
    • Power Supplies
    • Redundant Power Supplies
    • AT-LBM (Loop Back) Module
    • VCStack Stacking Module
    • AC Power Connector
    • Power Over Ethernet Plus (PoE+)
      • Power Classes
      • Power Capacity
• Chapter 2
  • Virtual Chassis Stacking
    • VCStack Introduction
      • Features of VCStacking
      • The Physical Stack
      • Resiliency Link
      • Resiliency Link Configurations via Switch Ports
    • Stack Formation
      • The Role of the Stack Master
      • Connecting switches into a stack
      • Steps to set up a VCStack
      • Steps to replace a stack member
      • Provisioning
• Chapter 3
  • Installing the Hardware
    • Reviewing Safety Precautions
    • Unpacking a Switch
    • Installing the Power Cord Retaining Clip
    • Installing the Switches in an Equipment Rack
    • Power Supply Module Installation
      • Overview
      • Installing a VCStack Stacking Module
    • VCStack Stacking Module Installation
      • Overview
      • Preparation
      • Installing a VCStack Stacking Module
      • Cabling an AT-StackXG Stacking Module
      • Cabling an AT-x6EM/XS2 Stacking Module
• Chapter 4
  • Cabling the Network Ports
    • Twisted Pair and Fiber Optic Specifications
      • Twisted Pair Cable Specifications
      • SFP and SFP+ Transceiver Specifications
    • Installing SFP and SFP+ Transceivers
    • Cabling the 10/100/1000Base-T and Fiber Optic Ports
    • Power Wiring to a DC AT-PWR250 Power Supply Module
    • AC Power Connection to a Power Supply Module
      • Starting a Local Management Session
    • Warranty Registration
• Chapter 5
  • Troubleshooting
    • Power LED is Off
    • Twisted Pair Port Link LED is Off
    • SFP or SFP+ LED is Off
    • Transceiver is Installed but the Status is “Not Present”
    • System Fault LED is Flashing
      • Two Flashes
      • Three Flashes
      • Five Flashes
      • Six Flashes
    • Cannot Establish a Local (Out-of-Band) Management Session
    • Switch Functions Intermittently
    • Issues with Virtual Stacking Chassis Configuration
• Appendix A
  • Technical Specifications
    • Physical Specifications
    • Environmental Specifications
    • Power Specifications
    • Certifications
    • RJ-45 Twisted Pair Port Pinouts
    • RJ-45 Style Serial Terminal Port Pinouts
    • AT-RPS3000 21-pin Connector Pinouts