Swiftech H20 220 APEX ULTRA REV2 User Manual
Page 10
Copyright Swiftech 2007 – All rights reserved – Last revision date: 10-08-07 - Information subject to change without notice – URL:
http://www.swiftech.com
Rouchon Industries, Inc., dba Swiftech – 3700 Industry Avenue, Suite 104, Lakewood, CA 90712 – Toll free (US) 888-857-9438 – Fax 562-595-8769 - E Mail:
PAGE 10 of 24
Packing List
COMPONENT ID
COMPONENT DESCRIPTION
QTY
USAGE
BHSC006C0-007SS
6-32 X 7/16 BUT HD CAP SS
4.00
WATER-BLOCK ASSEMBLY
O-RING 3/32
B1000-133 O-RING 3/32 X 1 13/1
1.00
WATER-BLOCK ASSEMBLY
APOGEE-H
APOGEE WATERBLOCK HOUSING
1.00
WATER-BLOCK ASSEMBLY
APOGEE-BRKT
APOGEE HOLD-DOWN PLATE
1.00
WATER-BLOCK ASSEMBLY
APOGEE-GT-BP
APOGEE GT BASE PLATE
1.00
WATER-BLOCK ASSEMBLY
BIG O-RING
BUNA-N 45MM ID
1.00
WATER-BLOCK ASSEMBLY
B1000-2.5X50
BUNA-N 70D BLACK O-RING
2.00
FITTINGS
PM4S-8BN
1/4" - 1/8 NPSM TO 1/2 ID
2.00
FITTINGS
22HC0672B
43/64" PREMIUM HOSE CLAMP
2.00
FITTINGS
SOCKET 775-BACKPLATE
SOCKET 775-BACKPLATE
1.00
INTEL® SOCKET 775
16FWRT004032
40-032 RETAINING WASHER
4.00
INTEL® SOCKET 775
13LTS2501400600
SPACERS
4.00
INTEL® SOCKET 775
LOCKWASHER6
LOCK WASHER #6
6.00
INTEL® SOCKET 775
M3X25-PAN-PHILIPPS
M3, 25 MM L, PHILIPPS
4.00
INTEL® SOCKET 775
WASHER-0148X0266X0040-91007A619
LOCK WASHER #6 X 0.040
4.00
AMD SOCKET 754/939/940,AM2 HARDWARE
90272A153-6-32X1.00-PHILIPS SCREW
6-32 X 1” PHILIPS SCREW
4.00
AMD SOCKET 754/939/940, AM2 HARDWARE
13RS040637
ROUND SPACER
4.00
AMD SOCKET 754/939/940,AM2 HARDWARE
APOGEE-AM2-BP
APOGEE AM2 BASE PLATE
1.00
AMD SOCKET AM2 HARDWARE
ST6977-0.250-34
3/16 HEX MALE FEMALE STANDOFF
4.00
NOCONA PACK
PPMS006C0016STZ1
6-32 X 1" PHIL PAN M/S STL
4.00
NOCONA PACK
16FW00432
WASHER
4.00
NOCONA PACK
13LTS2501400697
APOGEE NOCONA SPACER
4.00
NOCONA PACK
6-32 NUT
6-32 HEX M/S NUT STEEL
4.00
NOCONA PACK
ARCTIC CÉRAMIQUE
ARCTIC CÉRAMIQUE
1.00
THERMAL COMPOUND
Common installation guidelines
Removal of the motherboard is necessary to install the mounting posts in all cases, except for AMD® socket 754,
939, 940 and AM2.
The water-block may be installed in any direction. Simply rotate the water-block in your hand prior to fasten it to the
processor when you are filling up the circuit. This will purge it from any air bubbles.
The inlet and outlet are interchangeable with respect to flow direction.
Coolant: use of distilled water is mandatory. Swiftech’s HydrX coolant is recommended as an antifungal, and
corrosion inhibitor.
1. Step-by step
Install the fittings with their o-rings into the water block. Tighten each fitting until the flange of the fitting mates with
the ledge of the water-block, then lock it by adding ¼ to ½ turn.
Remove the existing heat sink from your motherboard.
Apply the provided Arctic Céramique thermal compound to the CPU following the comprehensive installation
instructions provided here:
http://www.arcticsilver.com/ceramique_instructions.htm
Install the Apogee water-block following the individual installation schematics for each type of CPU socket provided
hereafter.
Connect the tubing to the water-block hose-barbs. Use the provided hose-clamps to secure the tubing to the barbs.
2. Individual installation schematics
The Apogee GT ships pre-installed for socket 775. Both Nocona and AMD™(socket 754, 939, 940, AM2 and F) mounting hardware is
included