PerTronix Ignitor II 91247 - Manual (Page 2)

COMMON QUESTIONS AND ANSWERS
Q. The engine will not start or runs rough. What is the problem?
A. Perform Power and Ground Checks. Check all connections to insure that they are tight, and in
the proper location. Check all grounds; if a distributor ground wire was removed make sure that it
was reattached properly. Make sure that the red Ignitor II wire is supplied with a full 12 volts. The
Ignitor II is designed to sense high current levels, and shut off before damage occurs. Check all
wires for shorts, correct polarity and that the ignition coil’s primary resistance level is acceptable.
Q. . The vehicle will start, but then die. After waiting it will start again. What is wrong?
A. Perform Power and Ground Checks. The Ignitor II may have a “Low Voltage Problem.” If the
voltage supplied to the red Ignitor II wire is insufficient, the system may run for a period of time,
and then shut down as the voltage drops due to engine heat. The period may vary from minutes to
hours depending on available voltage and wiring condition. To remedy this condition refer to steps
2-4 of the wiring instructions.
Q. How do I check for a “Low Voltage Problem” or determine if I am getting adequate voltage?
A. Perform Power and Ground Checks. Also, to quickly test for a “Low Voltage Problem” or for
adequate voltage, remove the Ignitor II red wire from the coil positive terminal. Attach a jumper
wire from the battery positive terminal to the Ignitor II red wire. Try to start the vehicle. If the
vehicle starts with this test refer to steps 2-4 of the wiring instructions for further information.
Q. How do I check my coil for primary resistance?
A. Remove all wires from the coil. Set the ohmmeter to the lowest scale. Attach one lead of the
meter to the positive coil terminal. Attach the other lead to the negative coil terminal.
Q. May I modify the length of the wires?
A. Yes, you may cut the wires to any length your application requires. You may also add lengths of
wire if needed (20-gauge). Make sure that all wire splices are clean and the connections are tight.
Q. Will the Ignitor II work with aftermarket capacitive discharge boxes?
A. Yes, the Ignitor II is compatible with most CD boxes in the same respect as points. Use the CD
box wiring instructions for point systems and treat the Ignitor II black wire as a point wire. The
Ignitor II red wire should be attached to the 12-volt power source.
Q. Will the electronic shift assist in an OMC boat work with the Ignitor II?
A. The Ignitor II will work with all OMC stern-drive applications, when our “diode fix” is used. If
you’ve purchased a kit that didn’t include the “diode fix” diagram, call our tech line.
Q. How can I receive additional help?
A. Check our web site for current trouble shooting tips and up to date technical information. Log on
to www.pertronix.com. You may also contact our tech line at (909-547-9058)
3. Install the advance mechanism and the shaft back into the distributor.
IGNITOR II INSTALLATION.
1. Set the adapter plate into the distributor. Insert the provided hold down
stud through the plate and distributor housing.
2. Install the timing adjustment slide over the stud. Install the provided lock
nut.
3. Static timing the distributor by positioning the plate so the the slide is
positioned in the middle of the adjustment slot. The adjustment nut should
be centered with the cap spring clip (See illustration B). Tighten the nut
once it is aligned properly.
4. Install the plate retaining ring. The flat portion of the ring should be placed
on the adjustment slot side of the distributor.
5. Install the Ignitor II module onto the mounting studs.
6. Tighten the module into place with the hardware provided.
7. Attach the black Ignitor II wire to the coil negative contact stud mounted on
the plate. Tighten the wire down with the provided nut. (See illustration C).
8. Insert the red wire through the hole that was made in the distributor body.
9. Install the magnet sleeve onto the point cam.
10. Install the shim washer onto the distributor shaft.
11. Install the shaft support bracket. Spin the distributor shaft to align the
bracket and tighten in place with the 8-32 screws provided.
DISTRIBUTOR INSTALLATION.
1. Install the rotor.
2. Turn the rotor to the position that was noted prior to the removal of the
distributor.
3. Place distributor into block and fasten in place with the original mounting
bolts. Note: Do not force the distributor onto place. Check to make sure
that dive tang is properly aligned.
4. Instal the distributor cap.
5. Install the coil and coil retaining bail.
6. Install the spark plug wires.
WIRING.
1. Attach the Ignitor red wire and the Ignition wire to the coil positive
terminal.