Flame-thrower ii coil installation – PerTronix Flame-Thrower Coils 45111 User Manual
Page 2
LIMITED WARRANTY
PerTronix, Inc. warrants to the original Purchaser of its Flame-Thrower coils that
the product shall be free from defects in material and workmanship (normal wear and
tear excluded) for a period of 90 days from the date of purchase.
If within the period of the foregoing warranty PerTronix finds, after inspection,
that the product or any component thereof is defective, PerTronix will, at its option,
repair such products or component or replace them with identical or similar parts
PROVIDED that within such period Purchaser:
1. Promptly notifies PerTronix, in writing, of such defects.
2. Delivers the defective product or component to
PerTronix (Attn: Warranty) with proof of purchase date; and
3. Has installed and used the product in a normal and proper
manner, consistent with PerTronix printed instructions
THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENT
OR COMPONENTS SHALL CONSTITUTE THE SOLE REMEDY OF PURCHASER
AND THE SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT
OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE FOR
MONEY DAMAGES WHETHER DIRECT OR CONSEQUENTIAL.
440 East Arrow Highway
San Dimas, CA 91773
909-599-5955
www.pertronix.com
LIMITED WARRANTY
PerTronix, Inc. warrants to the original Purchaser of its Flame-Thrower coils that
the product shall be free from defects in material and workmanship (normal wear and
tear excluded) for a period of 90 days from the date of purchase.
If within the period of the foregoing warranty PerTronix finds, after inspection,
that the product or any component thereof is defective, PerTronix will, at its option,
repair such products or component or replace them with identical or similar parts
PROVIDED that within such period Purchaser:
1. Promptly notifies PerTronix, in writing, of such defects.
2. Delivers the defective product or component to
PerTronix (Attn: Warranty) with proof of purchase date; and
3. Has installed and used the product in a normal and proper
manner, consistent with PerTronix printed instructions
THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENT
OR COMPONENTS SHALL CONSTITUTE THE SOLE REMEDY OF PURCHASER
AND THE SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT
OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE FOR
MONEY DAMAGES WHETHER DIRECT OR CONSEQUENTIAL.
440 East Arrow Highway
San Dimas, CA 91773
909-599-5955
www.pertronix.com
1. Make sure the ignition switch is off or disconnect the battery negative cable.
2. Remove the coil wire from the coil tower.
3. Remove all wires from the positive coil terminal.
4. Remove all wires from the negative coil terminal.
5. Loosen the coil clamp and remove the existing coil.
6. Install FlameThrower II coil into the coil clamp and tighten into place.
Note: If the
Flame-Thrower II coil does not fit properly in the existing coil clamp, purchase
PerTronix chrome clamp #10002 or zinc clamp #10001.
7. Connect the wires that were removed from the negative coil terminal of the old coil
to the negative terminal of the Flame-Thrower II coil.
8. Connect the wires that were removed from the positive coil terminal of the old coil
to the positive terminal of the Flame-Thrower II coil.
9. Push the coil wire into the coil tower making sure that the boot is secure around the
coil tower.
FLAME-THROWER II COIL INSTALLATION
1. Make sure the ignition switch is off or disconnect the battery negative cable.
2. Remove the coil wire from the coil tower.
3. Remove all wires from the positive coil terminal.
4. Remove all wires from the negative coil terminal.
5. Loosen the coil clamp and remove the existing coil.
6. Install FlameThrower II coil into the coil clamp and tighten into place.
Note: If the
Flame-Thrower II coil does not fit properly in the existing coil clamp, purchase
PerTronix chrome clamp #10002 or zinc clamp #10001.
7. Connect the wires that were removed from the negative coil terminal of the old coil
to the negative terminal of the Flame-Thrower II coil.
8. Connect the wires that were removed from the positive coil terminal of the old coil
to the positive terminal of the Flame-Thrower II coil.
9. Push the coil wire into the coil tower making sure that the boot is secure around the
coil tower.
FLAME-THROWER II COIL INSTALLATION