PerTronix Flame-Thrower VW Billet Distributors - Manual

VW BILLET DISTRIBUTOR
INSTALLATION
LIMITED WARRANTY
PerTronix, Inc. warrants to the original Purchaser of its Flame-Thrower
Billet distributor that the product shall be free from defects in material and
workmanship (normal wear and tear excluded) for a period of 12 months
from the date of purchase (30 months when Ignitor III is purchased sepa-
rately).
If within the period of the foregoing warranty PerTronix finds, after
inspection, that the product or any component thereof is defective, PerTronix
will, at its option, repair such products or component or replace them with
identical or similar parts PROVIDED that within such period Purchaser:
1. Promptly notifies PerTronix, in writing, of such defects.
2. Delivers the defective product or component to
PerTronix (Attn: Warranty) with proof of purchase date; and
3. Has installed and used the product in a normal and proper
manner, consistent with PerTronix printed instructions
THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENT
OR COMPONENTS SHALL CONSTITUTE THE SOLE REMEDY OF
PURCHASER AND THE SOLE LIABILITY OF PerTronix WHETHER ON
WARRANTY, CONTRACT OR FOR NEGLIGENCE, AND IN NO EVENT
WILL PerTronix BE LIABLE FOR MONEY DAMAGES WHETHER DIRECT
OR CONSEQUENTIAL.
440 East Arrow Highway
San Dimas, CA 91773
909-599-5955
www.pertronix.com
GENERAL INFORMATION
1. See our website (www.pertronix.com) for latest product information.
IMPORTANT: Read all instructions before starting installation.
2. WARNING!!! DO NOT USE WITH SOLID IGNITION WIRES.
3. The Ignitor III used in our Flame-Thrower VW Billet distributor may
not be compatible as a trigger for other electronic boxes.
4. The Ignitor III Rev-Limiter is preset at 5500 RPM’s. The Rev-Limiter
can be user set to a minimum 4000 and a maximum 9000 RPM’s.
Note: It’s recommended that the Rev-Limiter be set to your
desired setting before installing the distributor.
5. All external resistors must be removed to achieve optimum
performance from the Ignitor III ignition system.
6. The Ignitor III is compatible with coils that have a minimum of 0.32 ohms of
primary resistance.
DISTRIBUTOR REMOVAL
1. Crank the engine until the first cylinder
in the firing order is at TDC “Top Dead
Center” on its compression stroke. The
timing indicator should point to TDC or 0.
2. Remove the distributor cap, and make
sure that the rotor is pointing towards the
contact on the distributor cap for the first
cylinder in the firing order.
3. Disconnect the battery negative (-) cable.
4. Disconnect all wires and hoses attached
to the distributor.
5. Remove the distributor hold down.
6. Remove the distributor and drive shaft spring.
7. VW’s only: Verify that the distributor drive
shaft slot is perpendicular to the engine case seam. See figure A.
8. Check the original distributor for excessive wear, or potential
problems.
9. Remove the distributor hold-down clamp from the original distributor
for use with the new distributor.
DISTRIBUTOR INSTALLATION
1. It’s recommended that the Rev-Limiter be set to your desired
setting before installing the distributor. See Rev-Limiter Settings.
2. Install the original distributor hold-down clamp onto the new
COMMON QUESTIONS AND ANSWERS
Q. The engine will not start or runs rough. What is the problem?
A. Check all connections to insure that they are tight, and in the proper location.
Visually check and measure all grounds. Remove
paint and corrosion from around
the distributor hold down bracket. Make sure that the distributor red and black wire
are connected properly.
The Ignitor III in the Flame-Thrower distributor will shut down
if the wires are incorrectly attached. The Ignitor III is designed to sense high current
levels. Check all wires for shorts, correct polarity and that the ignition coil’s primary
resistance level is acceptable. For more detailed information log on to www.pertronix.
com or contact the technical department at (909) 547-9058.
Q. The vehicle will start, but then dies. After waiting, it starts. What is wrong?
A.
The Ignitor III in the Flame-Thrower distributor may have a “Low Voltage Problem.”
If the voltage supplied to the red distributor wire is insufficient, the system may run
for a period of time, and then shut down as the voltage drops due to engine heat. The
period may vary from minutes to hours depending on available voltage and wiring
condition.
Q. How do I check for a “Low Voltage Problem” or determine if I am getting adequate
voltage?
A. To quickly test for a “Low Voltage Problem” or for adequate voltage (
Note: This is
only a test and is not intended as a permanent fix) attach a jumper wire from the
positive battery terminal to the positive terminal of the coil. Try to start the vehicle.
If the vehicle starts, low voltage is present.
Note: If the engine starts. The engine
will not turn off unless the jumper wire is removed from the positive battery
terminal. Check connections and insure all external resistors have being removed.
For more detailed information on how to locate the source of the voltage drop log on
to www.pertronix.com or contact the technical department at (909) 547-9058.
Q. How do I check my coil for primary resistance?
A. Remove all wires from the coil. Set the ohmmeter to the lowest scale. Attach one
lead of the meter to the positive coil terminal. Attach the other lead to the negative
coil terminal.
The Ignitor III in the Flame-Thrower distributor is compatible with coils
having a resistance of 0.32 ohms or greater.
Q. May I modify the length of the wires?
A. Yes, you may cut the wires to any length your application requires. You may also
add lengths of wire if needed (20-gauge). Make sure that all wire splices are clean
and the connections are tight.
Q. Will the Ignitor III in the Flame-Thrower distributor work with aftermarket capacitive
discharge boxes?
A.
We recommend the Ignitor or Ignitor II as a trigger source for a capacitive
discharge box. For more detailed information log on to www.pertronix.com or
contact the technical department at (909) 547-9058.
Q. How can I receive additional help?
A. Check our web site for current trouble shooting tips and up to date technical
information. Log on to www.pertronix.com. You may also contact our tech line at (909)
547-9058.
0019-008712 03-14
Figure A