Panasonic SCPMX9EG - Manual (Page 6)

VQT4Z2
1
6
6
ENGL
ISH
Network settings
You can stream music from an iOS device (iPhone, iPod,
iPad), an Android™ device or a Mac/PC to this system’s
speakers by using the AirPlay or DLNA feature.
To use these features, this system must join the same
network as the AirPlay compatible device (> 9) or the
DLNA compatible device.
• It is also possible to use AirPlay without a network router.
(> 10, “Directly streaming to this system (AirPlay)”)
• Switching between a wired LAN connection and a wireless
LAN connection may cause the connection settings to be
initialized. In that case, make the settings again.
• For a stable connection to the network, a wired LAN
connection is recommended.
Normally, just connecting a LAN cable will complete the setup.
1 Connect the main unit to a broadband router, etc.
using LAN cable while the AC mains lead is
disconnected.
2 Connect the AC mains lead to the main unit and
turn this system on.
This unit is ready for use when “
” is indicated on
the display.
• The LAN cable must be connected or disconnected
while the AC mains lead is disconnected.
• Use category 5 or above straight LAN cables (STP)
when connecting to peripheral devices.
• Inserting any cable other than a LAN cable in the LAN
port can damage the unit.
• When a LAN cable is connected, wireless settings will
be cancelled.
This system has built-in Wi-Fi ® and can be connected to
a wireless router.
Preparation
• Place this system as close to the wireless network
router as possible.
• Disconnect the LAN cable.
• Point the antenna on the rear of
the main unit up as shown in the
figure.
• Do not perform the following:
- Tilting the antenna forward or
backwards when it is pointing up
- Applying too much force to the
antenna
- Carrying this unit by holding the antenna
1 Turn this system on.
2 Follow the chart below to choose the network
setting method.
Wired LAN connection
LAN Cable
(not supplied)
Broadband router, etc. e.g.,
You can perform network-related settings individually.
jIf your home wireless network has been configured to
use specific IP Addresses, Subnet Mask, Default
Gateway, Primary DNS, etc.
jIf you want to change the name of this system that is
displayed as the AirPlay speakers or DLNA renderer.
1 Connect the main unit directly to your computer using
LAN cable while the AC mains lead is disconnected.
2 Connect the AC mains lead to the main unit and turn
this system on.
3 After “ ” is indicated on the display, check the IP
address for this unit. (> 15, “IP/MAC Address”)
4 Press [SETUP] on the remote control repeatedly to
select “Net Setup” and then press [OK].
5 Press [SETUP] on the remote control repeatedly to
select “Manual” and then press [OK].
6 When “Setting” blinks on the display, start an Internet
browser on your computer and then type the IP address
for this unit checked in step 3 into the address field and
display the setup screen.*
7 Select and input the details.
8 Select “JOIN” to apply the settings.
9 The settings are completed when “Success” is displayed.
10 Turn off this unit and then disconnect the AC mains lead.
11 Perform “Wired LAN connection”. (> left)
* It may take a few minutes until the setup screen is
available to be displayed on the browser depending on
the environment.In that case, reload the browser.
Wireless LAN connection
Wireless router, etc. e.g.,
Does your wireless network router support
WPS?
Yes
l 7,
“Method 1”
l 7,
“Method 2”
l 7,
“Method 3”
No / Do not know
Yes No
Are you using an
iPod touch/iPhone/iPad?
Is the iOS version 5.0 or later?
SC-PMX9EG-VQT4Z21.book 6 ページ ２０１３年３月２２日 金曜日 午後４時５４分