Vaddio ClearVIEW HD-USB PRO - Manual (Page 12)

WallVIEW HD-USB PRO Camera System
WallVIEW HD-USB PRO Camera System Document Number 342-0467 Rev. E Page 12 of 40
Step 4: Leave the IR out OFF (up) as default.
Step 5: Use 9600bps for control speed as default.
 If the camera has been inverted, then set the Image Flip to ON, otherwise leave it off.
 The test bars are really, really, totally non-standard (horizontal - just to mess with the old-timers) and will
override the video output. These test bars are 75% IRE. Use the test bars for…testing (kind of obvious).
The HD-USB camera uses UVC drivers and does not require the loading of any other drivers to run on the PC.
As long as the operating systems and soft-client software support UVC drivers, no additional software, other than
the application, is required.
S TEP BY S TEP I NSTRUCTIONS TO INSTALL THE W ALL VIEW HD-USB PRO C AMERA S YSTEM
Step 1: Locating the Camera
Locate the camera mounting position while paying close attention to camera
viewing angles, lighting conditions, possible line of site obstructions, and
checking for in-wall obstructions where the camera is to be mounted. Pick a
mounting location to optimize the performance of the camera.
Like all Vaddio WallVIEW systems, the WallVIEW HD-USB PRO is easy to
install and operate. The product was specifically designed with Cat-5 cable
connectivity for the extension both the power and USB 2.0 signals.
Step 2: After determining the optimum location of the camera system, run two (2) Cat-5 or better cables (if using
both the Extreme USB 2.0 Extenders and the Power Extension Module) from the computer location to the camera
location. Using both extenders together will limit the overall Cat-5 cable distance to distance to 150’. If using the
Extreme USB 2.0 Extenders alone with local camera power, the a single Cat-5 cable can be run up to 328.1’
(100m) between the extenders TX and RX units. Make sure to mark and test the Cat-5 cable(s) and use any real
RJ-45 crimper and connectors using the 568B straight-through wiring standard. Please do not use the “feed-thru”
type RJ-45 connectors for professional installations.
Step 3: Using the Thin Profile Wall Mount directions, install the mount. If mounting to the drywall with wall
anchors, use four (4) quality wall anchors. Make sure to level the mount and tighten the mounting screws.
Step 4: Connect the Cat-5 cable to the EZ POWER VIDEO RJ-45 port on the back panel of the HD-USB camera.
Connect 1’ (305mm) USB 2.0 Cable Type-B Male into the USB Type-B Female on the back panel of the HD-USB
camera. Connect the Type-A Male into the Extreme USB 2.0 Extender TX unit’s Type-A Female jack. Plug the
USB CAT-5 cable into the RJ-45 Link Port of the TX Extender unit. With the supplied 1’ (305mm) EIAJ-03 to
EIAJ-03 power cable, connect one side to the 5 VDC supply on the camera and the other end to the Extreme
USB 2.0 TX Extender unit’s 5 VDC input. With the supplied Velcro, find a place on the back of the mount to
attach the USB extender and field dress the cabling to hide as much as possible.
NOTE: Check all Cat-5 cables for continuity in advance of the connection. Do not plug the
Power Extension Module Cat-5 cable into any other RJ-45 port but the EZ POWER VIDEO
port. There is 24 VDC Volts on Pins 1 & 2. Plugging into any other port may cause
damage to the camera system and void the warranty.
Step 5: At the Head-End
Plug the other end of the Power Extension Module’s CAT-5 cable into the RJ-45 port of the Power Extension
Module Marked EZ POWER VIDEO. Plug the USB extender’s CAT-5 cable into the RJ-45 Link Port of the
Extreme USB 2.0 Extender RX unit at the computer. With a USB 2.0 cable connect the USB Type-B Male to the
Type-B Female on the extender and the other end, Type-A Male into the computer.
WallVIEW HD-USB PRO