Vaddio WallVIEW HD-20 - Manual (Page 9)

WallVIEW HD-20
WallVIEW HD-20 Manual 342-0179 Rev. C Page 9 of 16
NOTE (One more time!): Check all Cat-5e cables for continuity in advance of the final
connection. Label the Cat-5e cables. Plugging the EZ POWER HD VIDEO cable into the
wrong RJ-45 may cause damage to the camera system and void the warranty.
Step 7: Connect the Vaddio 24 VDC power supply to an AC outlet. Power will travel down the Power/Video Cat.
5 cable to the camera. The camera will “Home” to a centered position ready for control information from the IR
remote control or RS-232 camera controller of the integrators’ choice. To insure proper continuity of control and
operation of the cameras, the RS-232 controller (control system or joystick) should be powered on after the
camera.
General Specifications:
WallVIEW HD-20
Part Numbers WallVIEW HD-20 999-6955-000 (North America)
WallVIEW HD-20 999-6955-001 (International)
Vaddio ClearVIEW HD-20
Image Device 6.49mm diagonal (1/2.8 Type) Exmor High-speed CMOS Image Sensor
Picture Elements 3.27M pixels (Effective)
HD Resolutions 1080i/59.94/60, 1080/50i, 720p/59.94/60, 720/50p, 1080/30p and 1080/25p (SD Resolutions not Supported)
Lens 20x Optical Zoom, 11-Element HiLD™ (High Index Low Dispersion) Glass
Focal Length F=4.7mm wide end to 94mm tele end
Horizontal Viewing
Angle (16:9 format) 1080i Mode: 2.9° tele end to 55.2° wide end
720p Mode: 1.93° tele end to 36.8° wide end (windowed - not scaled)
Invertible Yes - With No Frame Delay
Video S/N Ratio >50 dB
Minimum Illumination 1.6 LUX (F1.6, 50IRE)
Serial Control Protocol RS-232 (Modified VISCA)
Min. Object Distance Wide End: .01m wide end, Tele end: 1.0m
Pan Range +170 degrees to -170 degrees
Tilt Range +90 degrees to -30 degrees
HD Video Select 16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings 10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, Unpublished Functions
Preset Positions 16 (internal), 6 recalled via IR Remote
Dimensions/Weight 7.81” (198.37mm) x 6.67” (169.42mm) x 7.057” (179.25. mm), 5.61 lbs. (2.54011744 kg.)
Quick-Connect SR (Short Range) Interface
Connectors  Power Connector: 5.5mm OD, 2.5mm ID coaxial connector

Power/Video RJ-45: Supplies power to, and component HD from the camera, up to 100 feet

Video Output: DE-15 connector for HD Analog Component (YPbPr) video only (No SD Support)

IR Output: Transmits modulated or non-modulated IR signals received from the HD-20 IR receiver
 Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
 Control Out RJ-45: Sends RS-232 from Quick-Connect SR to the camera
Cat. 5 Cable Distance Up to 100’ (30.5m)
Power Supply 24 VDC, 2 Amp
Dimensions 1.6” (40.64mm ) H x 5.5” (139.7mm) W x 3.25” (82.5500000000001mm) D -1/3 Rack Size
Rack Mount Adapter Accessory: 998-6000-002 - Holds three (3) Quick-Connect SR Interfaces
CONCEAL Wall Mounting System for Vaddio ClearVIEW HD-20
Dimensions 5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight Approx. 2.4 lbs. (1.1kg)