Fagor 3CFT-TILE - Manual (Page 6)

6
• Only for chimney installation: Apply the support
bracket „G“ to the adherent ceiling, use the chimney
support bracket as a hole scheme (if present, the small
eyelet found on the support should coincide with the line
previously traced on the wall) and trace with a pencil 2
holes, drill the holes (Ø8mm), insert 2 plugs.
Fasten the support bracket to the wall with 2 5x45mm
screws (4).
• Open the vapour scheme and remove the grease filters
(see relevant paragraph).
• Hang the hood (5), regulate the position (6-7) and fasten
it securely with one screw and washer(8).
• Carry out electrical connections (9), but leave the hood
disconnected from the general electrical main panel.
• Install the flange supplied on the exit hole of the hood
(10a).
Note – only for installation without chimneys: In case
you want to use the hood in filtering version, install the
grille/deflector instead of the flange (10b).
• Carry out the connection of one tube (11 – tube and ties
for fastening not included, they need to be bought) for the
fume discharge to the connection ring placed on top of
the extractor motor unit.
The other end of the tube should be connected to a fume
expulsion device towards the outside, in case the hood is
used in extractor version.
• Fix the upper cover with 3 screws.(12)
Note: this is supplied already mounted in some cases.
• Only for chimney installation: In case you want to use
the hood in filtering version, fasten the deflector F to the
support bracket, and connect the other side of the tube to
the connection ring placed on the deflector (13).
Apply the chimneys and fasten them on with two screws
(14a) to the chimney support bracket „G“ (14b). and
make the lower part of the chimney slide into the suited
part on top of the chimney.
• Mount the grease filters and close the vapour scheme.
Warning! If the hood has to be used in extractor version,
remove, if supplied, the carbon filter and the fastening
wand (placed on the back of the grease filters – see
relative paragraph).
If the hood has to be used in filtering version, make sure
that the carbon filter is already mounted on the back of
the grease filter, or in case it’s missing, buy it and install
it.
Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Perimeter suction panel
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction
power) - duration 5 minutes - press again to
return to previous setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power)
- when flashing it indicates the need to wash or
replace the carbon filter. This signal is normally
deactivated. Press keys 1 and 2 at the same
time to activate it. At first only key 1 will flash
and then both keys 1 and 2 to indicate
activation. Repeat the operation to deactivate
the signal. At first keys 1 and 2 will flash and
then only key 1 to indicate deactivation.
Low-speed selection key (suction power) –
when flashing it indicates the need to wash the
fats filter.
Motor key OFF (stand by) – excludes the
electronics – reset wash/replace filters signals.
MOTOR OFF
Press briefly to switch the motor off.
RESET FILTERS SIGNALS
After having carried out maintenance of the
filters, press the key for 3 seconds. Flashing led
1 (fats filter) or 2 (carbon filter) will stop
flashing.
EXCLUDING THE ELECTRONICS
Press the key for 3 seconds. The hood
command electronics will be excluded.
This function can be useful during the product
cleaning operations.
Just repeat the operation to reinsert the
electronics.
The perimeter suction panel must always be left closed and
opened only for maintenance (e.g. cleaning or changing
filters).
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.