Lenovo IdeaCentre A700 User Manual

Method

Advertising

Note: The remote control cannot turn the computer on. When using

the computer for the first time, you need to establish a connection

from the wireless keyboard and mouse to the computer. See section

Wireless keyboard and mouse instructions on this flyer for more

details.

Connect the power adapter to the computer and the electrical outlet as shown above.

Press the power button on the side of the computer to turn it on.

Computer stand instruction

Important information on how to use this computer

Computer instruction

Wireless keyboard and mouse instructions

35˚

Use the stand to position the display to your preference. It can be

rotated between 12º and 35º from the vertical position.

The stand provides stability to the computer; it is not a removable part.

Attention:

1. The computer stand must remain installed at all times to ensure

maximum system stability.

2. Make sure the angle of the computer is at least 12 degrees from the

vertical positon; otherwise the computer will be unstable and could

fall over.

The computer can be mounted on the wall.

To mount the computer on the wall, you need to install a wall mount VESA bracket adapter* ( some models

are shipped with this part) on the back of the computer as following steps. Using this bracket adapter to install

a VESA standard wall mount (purchased separately) to make the computer mounted on the wall.

Note: For this procedure, it helps to place the computer face-down on a soft flat surface. Lenovo recom-

mends that you use a blanket, towel, or other soft cloth to protect the screen surface from scratches or other

damage.

VESA bracket adapter*: VESA100, 100mm x 100mm, M4 bolts.

1. Pull the computer stand up

and slide the little pin up in

the hinge to fix the stand.

2. Remove the 2 screws that

secure the stand to the com-

puter rear cover.

3. Install the metal bracket on to

the computer.

Card reader
IEEE 1394 port
Headphone port
Microphone port
USB ports (2)
Optical drive slot

Hold the computer tightly when you carry it.

TV tuner port (selected models)
Wireless reset button
AV-IN ports
USB ports (4)
Ethernet port
SPDIF port
HDMI in port
HDMI out port
Power socket

Notes:

1) When establishing a wireless connection, it

is recommended to keep the distance from

the keyboard/mouse to the computer less

than 25 cm (10 inches)

2) The effective working distance of the

wireless keyboard and mouse is 10 m (33

feet) (depending on the computer's working

environment).

If the wireless device does not work, do the

following:

1. Be sure there is no physical obstacle

between the wireless device and the

computer.

2. Restart the computer, and verify that the

system devices are functional.

3. Repeat the procedure for establishing a

Bluetooth connection.

4. Replace the batteries.

5. Do not place the computer under a metal

surface or table.

6. Make sure there are no electronic devices

close by, such as speakers, remote

controls of electronic toys or mobiles, which

might create high electromagnetic fields

that could interrupt the wireless connection.

7. Place the keyboard, mouse and remote

control the right way up.

8. Remove the batteries from the keyboard,

mouse and remote control if you do not

plan to use them for a long time.

9. If the batteries in the keyboard, mouse or

remote control leak, clean the battery

compartments as soon as possible and

insert new batteries.

10. Use batteries of good quality to ensure the

proper functioning of the remote control.

11. When battery power becomes low, the

battery indicator light on the keyboard will

change from orange to red.

The buttons at the bottom of the screen are touch buttons. When you touch these, the indicator lights turn on.

3
4

When the battery indicator light blinks red, it means that

the battery power becomes low.

When the battery indicator light blinks white, it means that

the keyboard or mouse is being connected.

LVT

LVT :

After entering Windows, press this key to launch the

LVT (Lenovo Vantage Technology) program, Lenovo's

pre-loaded Home PC software. In addition to its own

functions, the LVT program will allow you to start other

Windows compatible software, specially configured to

run on this model of computer.

Before using the accompanied

peripherals, carefully read the

detailed information in the Safety

and Warranty Guide. Since differ-

ent models have different periph-

erals, you might not find all of the

described items depending on the

actual model you purchased.

Built-in microphone
Camera
Power button
Hard Disk Drive Indicator
Bluetooth status indicator
WIFI status indicator
Indicator lights ON/OFF button

Volume down
Volume up
Brightness down
Brightness up
Novo Vision button
PC mode / HDMI-in /

AV-in switch combo
LCD On/Off

Method

1. Install the batteries.

1. Make sure the indicator lights blink.

2. Press the wireless reset button until wireless connection established.

2. Turn on the power switch.

3. Press the wireless connect button.

4. Make sure the indicator lights blink and then turn on the computer.

5. Establish the wireless connection automatically.

Put 2 AA batteries in the

keyboard's battery compartment.

2 AA batteries

Turn on the mouse power switch.

If you do not plan to use the mouse for

a long time, turn off the mouse power

switch to save battery life.

When the keyboard and mouse wireless indicator

lights blink white, turn the computer on within 30

seconds to establish a wireless connection.

Put 2 AA batteries in the battery

compartment, making sure the position

of the polarities is identical to the image.

After installing the

batteries, turn on

the power switch on

the side of the

keyboard.

Once the wireless connection is

successfully established, the indicator lights

on the keyboard and mouse will turn off and

they will work properly.

While the computer is turned off, press the

wireless connect buttons on the back of the

keyboard and mouse.

OFF STA

Battery

compartment

If the wireless keyboard and mouse fail to connect according

to method A, follow method B:

Make sure the wireless

indicator lights still blink.

If they stop blinking,

press the connect

button on the back of

keyboard and mouse

again.

If connection is not established successfully, refer to "Wireless

keyboard and mouse instructions" in the User Guide.

To establish the wireless

connection, press the

wireless reset button on the

back of the computer for over

6 seconds until the indicator

lights of the keyboard and

mouse turned off.