AMX Modero NXD/NXT-1200VG User Manual
Vg series modero, Touch panels
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- VG Series Modero® Touch Panels
- Introduction
- Touch Panel Accessories
- Overview
- NXA-AVB/RGB Breakout Box (FG2254-11)
- Product Specifications
- RGB RJ-45 connection and wiring information
- Using the HD-15 high-density connector
- Installing the NXA-AVB/RGB
- Wiring the NXA-AVB/RGB connectors and cables
- Wiring the NXA-AVB/RGB for Unbalanced Audio
- Wiring the NXA-AVB/RGB for Balanced Audio
- Preparing your panel for Pass-Thru Control (using the NXA-AVB/RGB Breakout Box)
- Wiring for Pass-Thru Computer Control
- NXA-MTC/RGB Combo Table Top Cable (CA2250-70)
- NXA-RGB RGB/VGA Interface Card (FG2260)
- NXA-CFTP Compact Flash (FG2116-22)
- NXA-PCI80211G Wireless Card (FG2255-04)
- Installation and Upgrade of the Internal NXT Components
- Installation and Upgrade of the Internal NXD Components
- NXT-BP Power Pack (FG2255-10)
- NXA-BASE/B Battery Base Kit (FG2255K)
- NXT-CHG Battery Charger Kit (FG2255-50K)
- Installation Procedures: 12" and 15" Panels
- Overview
- Unpacking the Panel
- Installing Internal Components
- Upgrading to the MB-TP12/MB-TP15 VESA Mounting Kit
- Pre-wall Installation of the Conduit Boxes
- Installation of the NXD Touch Panel
- Wiring Guidelines for the 1200VG and 1500VG Panels
- Audio/Video Port: Connections and Wiring
- Ethernet/RJ-45 Port: Connections and Wiring
- Installation Procedures: 17" Panels
- Overview
- Unpacking the Panel
- Installing the Internal Components
- Upgrading the Back Box with the MB-TP17 VESA Housing
- Pre-wall Installation of the CB-TP17 Conduit Box
- Installation of an NXD-1700VG
- Wiring Guidelines for the 1700VG Panels
- Audio/Video Port: Connections and Wiring
- Ethernet/RJ-45 Port: Connections and Wiring
- Panel Calibration
- Configuring Communication
- Overview
- Modero Setup and System Connection
- Configuring and Using USB with a Virtual Master
- Step 1: Setting up the USB Driver on the PC
- Step 2: Confirming the Installation of the USB Driver on the PC
- Step 3: Confirm and View the current AMX USB device connections
- Step 4: Using a USB to Configure a Virtual Master (using NetLinx Studio)
- Step 5: Confirm and View the current AMX USB device connections
- Wireless Settings Page - Wireless Access Overview
- Configuring a Wireless Connection
- Step 1: Configuring the Panel’s Wireless IP Settings
- Step 2: Configuring the Card’s Wireless Security Settings
- Configuring a Wired Ethernet Connection
- Step 1: Configuring the Panel’s Wired IP Settings
- Step 2: Choosing a Master Connection Mode Setting
- Step 3: Configuring the Ethernet Connection Type
- Using G4 Web Control to Interact with a G4 Panel
- Using your NetLinx Master to control the G4 panels
- Upgrading Modero Firmware
- Firmware Pages and Descriptions
- Overview
- Setup Navigation Buttons
- Setup Page
- Panel Information Page
- Project Information Page
- Time & Date Settings Page
- Audio Settings Page
- Supported sampling rates for WAV
- Information icon
- Protected Setup Page
- Video Slide-Out Menu
- Video Settings Page
- Video - RGB Settings Page
- Adjusting the Incoming Signal on the RGB Settings Page
- Video - Streaming Settings Page
- Battery Base Page
- Protected Setup Navigation Buttons
- Protected Setup Page
- Security Settings
- System Settings Page
- Sensor Settings Page
- Using the Automated Brightness Control feature (DIM Mode)
- Calibration Page
- G4 Web Control Settings
- Other Settings Slide-Out Menu
- Cache Settings Page
- Setting the image cache
- Clearing the image cache
- Checking image cache status
- Password Settings Page
- Tools Slide-out Menu
- Panel Connection Logs
- Checking the Panel Connection Logs
- Refreshing the Panel Connections Log
- Clearing the Panel Connections Log
- Panel Statistics
- Checking the Panel Statistics
- Refreshing the Panel Statistics
- Clearing the Panel Statistics
- Connection Utility
- Using the Connection Utility
- Wireless Settings Page
- Displaying Stream Content
- Programming
- Overview
- Button Assignments
- Page Commands
- Programming Numbers
- "^" Button Commands
- ^ANI
- ^APF
- ^BAT
- ^BAU
- ^BCB
- ^BCF
- ^BCT
- ^BDO
- ^BFB
- ^BIM
- ^BLN
- ^BMC
- ^BMF
- ^BMI
- ^BML
- ^BMP
- ^BNC
- ^BNN
- ^BNT
- ^BOP
- ^BOR
- ^BOS
- ^BPP
- ^BRD
- ^BSF
- ^BSM
- ^BSO
- ^BVL
- ^BVN
- ^BVP
- ^BVT
- ^BWW
- ^CPF
- ^DPF
- ^DTO
- ^ENA
- ^FON
- ^GDI
- ^GIV
- ^GLH
- ^GLL
- ^GRD
- ^GRU
- ^GSC
- ^GSN
- ^ICO
- ^JSB
- ^JSI
- ^JST
- ^MBT
- ^MDC
- ^SAV
- ^SHO
- ^SKT
- ^STO
- ^TEC
- ^TEF
- ^TOP
- ^TXT
- ^UNI
- ^VTO
- Text Effect Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded Codes
- Panel Setup Commands
- Dynamic Image Commands
- Troubleshooting
- Appendix