AEG SRP 4335 CD-MP3 - Manual (Page 39)

English
39
AUX IN socket
To connect analogue replay devices. Via this socket you can
also hear the sound of other playback devices such as MP3
players, CD players etc. through the loudspeakers.
1. Please connect the external device with a 3.5 mm stereo
jack plug to the AUX IN socket (27).
2. Turn the function selector switch (24) to the AUX/TAPE
position.
3. Through the loudspeakers you can hear the playback of
the sound from the external device; with the VOLUME
control (1) you can change the volume. The CD buttons
do not have any function.
4. For the remaining procedure please see the operating
instructions of the external sound source.
NOTE:
• Adjust the volume of the external device to a comfort-
able level.
• To connect external microphone, electric guitar,
etc.: Due to the different signal levels, you may need a
preamplifier which is available at your local dealer.
USB port (6)
This device has been designed according to the latest state
of the art in USB technology. The large number of different
USB devices of all kinds on the market today makes it impos-
sible to guarantee full compatibility with all USB storage
media. For this reason, problems during playback from USB
storage media may occur in rare cases. This is
no malfunction
of the device.
1. Turn the function selector switch (24) to the MEDIA posi-
tion.
2. Connect a USB device directly to the USB port.
3. Press and hold the STOP/USB/CARD button (16) and
select USB mode. USb will be displayed.
4. After a few seconds, the total number of folders and
tracks will be displayed. Playback will start subsequently.
5. The display will show the current song, the symbol ,
MP3 and USB.
See chapter “Playing CDs/MP3” for more information.
NOTE:
• The USB port will be automatically selected if there is
no CD loaded in the CD drive.
• Always directly connect a USB storage medium to the
USB port to prevent any malfunctions.
• The USB connection is not suitable for charging exter-
nal devices.
CAUTION:
Slide the function selector (24) to the RADIO position
before disconnecting the USB device.
Card Slot (7)
1. To play data from an SD/MMC card, insert it into the card
slot.
2. Turn the function selector switch (24) to the MEDIA posi-
tion.
3. Press and hold the STOP/USB/CARD button (16) and
select USB mode. USb will be displayed. Now press and
hold the STOP/USB/CARD button again to select SD
mode. Sd will be displayed.
4. After a few seconds, the total number of folders and
tracks appears on the display. Playback starts subse-
quently.
5. The display will show the current song, the symbol ,
MP3 and USB.
For more information on operation, see chapter “Playing
CDs/MP3”.
NOTE:
The card slot is automatically selected if there are no CD
loaded in the CD drive and no USB storage media con-
nected.
CAUTION:
Before you remove the memory card, switch the device to
Radio operation.
Listening to the Radio
1. Turn the function selector switch (24) to the RADIO posi-
tion.
2. Use the band selector switch (22) to select the desired
frequency band.
VHF (Stereo) = FM ST., VHF = FM,
Medium wave = AM (Mono)
3. Tune in the desired station with the station adjustment
knob TUNING (4).
4. For VHF/FM mode pull out the telescopic antenna (30)
and turn it to improve reception. If the reception is too
weak and there is interference on the station being
received, we recommend switching to FM.
5. An aerial is integrated into the device for the reception of
AM stations. The machine can be aligned to the station
by turning it. In this frequency band programs are trans-
mitted in “mono” only.
Cassette Operation
Playing Cassettes
1. Turn the function selector switch (24) to the AUX/TAPE
position.
2. Press the / stop/eject button (11) to open the cassette
compartment (9).