English – AEG AR 4020 User Manual

Page 69

Advertising

ENGLISH

Further Settings with the Multi Control Knob

Press and hold the multi control knob (21) to access

further setting options. Each further pressing of the

multi-controller switches to the next set point.

Turn the multi control knob to change the displayed

setting.

The following settings are possible:

BEEP

Key tone:

BEEP 2ND:

■

The unit sounds a beep tone

when you press and hold a multifunctional

button.

BEEP ALL:

■

The unit sounds a beep tone

every time you press a button.

BEEP OFF:

■

The unit sounds no beep tone.

AREA

Region, when the unit is used.

Europe (

EUR) or USA

NOTE

Changing this setting deletes all station

►

presets.

Traffic announcements

TA SEEK:

■

With activated TA function the

unit searches for a station with traffic an-

nouncements.

TA ALARM:

■

No automatic station search.

The unit sounds a beep tone if no traffic

information is received and

NO TP/TA is dis-

played.

SEEK PI is displayed if the selected

station does not transmit an RDS signal.

Moving into an area where two stations

with identical AF, but different Pl code (PI =

program information) are received destabilizes

reception. In this situation you have two op-

tions:

PI SOUND:

■

To change stations the other

station is played for less than one second.

PI MUTE:

■

The other station is muted.

RETUNE Delay for automatic search with traffic an-

nouncements and/or program information:

■ (Short) after approx. 30 seconds

■ (Long) after approx. 90 seconds

MASK

Setting to mask station during search:

DPI:

■

Alternative frequencies with different

Pl code are excluded from the search.

ALL:

■

Alternative frequencies with different

Pl code and no RDS information with high

signal level are excluded from the search.

Loudness Function

Press and hold

BAND/LOU/ENT (2) to activate the

Loudness function.

LOUD ON is displayed. The Loud-

ness function enhances the bass frequencies.

Press and hold

BAND/LOU/ENT (2) again to deactivate

the Loudness function.

LOUD OFF is displayed.

Sound Settings

Repeatedly press

EQ/TA (19) to cycle through the

settings

FLAT, CLASSIC, POP, ROCK or EQ OFF. The

selected setting is displayed.

Display Information

Repeatedly press

DISP (14) to cycle through the following

display information:

Time (is automatically set if RDS reception is enabled),

radio station, programme type, frequency of the currently

set radio station, information on file names (only during

playback of a MP3 or WMA file).

NOTE

If no information is available

►

NO CLOCK or NO PTY is

displayed.

If the information is too long for the display, it is

►

displayed as scrolling text.

Setting the time manually (in Radio Mode)

If the time should not be set automatically, proceed as

follows:

Press the button

DISP (14) for a short while until the

time appears on the display.

Now keep the button

DISP pressed until the minutes

flash.

Turn the multi-controller (21) to make the setting.

Press the button

DISP for a short while. The hours start

flashing.

Turn the multi-controller (21) to make the setting.

Reset Radio

To reset the unit to default settings press

RESET (25) with

a pointed object, i.e. pen.

Reset the unit when:

using it the first time after all cabling is done,

malfunctions of buttons occur,

error messages are displayed.

Radio Functions

Set RADIO Mode

Repeatedly press

MODE (20) until frequency and band

are displayed.

Select Frequency Band

Press

BAND/LOU/ENT (2) to toggle between FM1, FM2,

FM3 and AM. The selected frequency band is displayed.

Auto Search

Press

(15) or (16) to start auto search,

SEARCH is

displayed. Search stops if a station is found.

Manual Search

Press and hold

(15) or (16) until

MANUAL is

displayed.

Advertising