Programming signals from other remote controls, Erasing one of the remote control button settings, Controlling the rest of your system – Pioneer VSX-923-S User Manual

Page 72

Advertising
background image

72

 

 

 

 

10

Controlling the rest of your system

4 Repeat steps 2 through 3 for the other components you want to control.

To try out the remote control, switch the component on or off (into standby) by pressing u SOURCE. If it doesn’t
seem to work, select the next code from the list (if there is one).

5 Press RCU SETUP to exit the preset setup mode.

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you
can program signals from the remote control of another component. This can also be used to program additional
operations (buttons not covered in the presets) after assigning a preset code.
The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer
format only).
Certain buttons represent operations that cannot be learned from other remote controls. The buttons available
are shown below:

RECEIVER

D.ACCESS

CH LEVEL

DIMMER

SLEEP

SIGNAL SEL

SPEAKERS

MPX

PRESET

TUNE

BAND

PTY

ZONE 2

ZONE 3

HD ZONE

CLASS

FEATURES

+Favorite

Z2

Z3

HDZ

HDMI OUT

MCACC

AUTO/ALC/

DIRECT

AUTO

S.RTRV

STANDARD ADV SURR

OPTION

P.CTRL+

PHASE

ECO

PQLS

ENTER

/ CLR

CH

CH

22

5

4

6

8

0

7

9

1

3

2

AUDIO

DISP

iPod CTRL

HOME

MENU

INPUT SELECT

iPod

USB

CBL

STATUS

SAT

TUNER

MHL

ADPT

CD

TV

RCU SETUP

STANDBY/ON

BDR

BD

DVD

DVR

NET

HDMI

RECEIVER

MUTE

VOLUME

TOP MENU

VIDEO

PARAMETER

AUDIO

PARAMETER

RETURN

TOOLS

MENU

ALL ZONE STBY

DISCRETE ON

CH

TV CONTROL

INPUT

VOL

ENTER

SOURCE

1 Press and hold RCU SETUP, then press ‘2’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To “learn” codes at the TV CONTROL buttons, proceed to step 3.
! To cancel the preset setup mode press RCU SETUP.

2 Press the input function button for the component you want to control.

The LED blinks once and flashes continuously.

3 Point the two remote controls towards each other, then press the button that will be
doing the learning on this receiver’s remote control.

The LED flashes once, then stops flashing, remaining lit.

! The remote controls should be 3 cm apart.

3 cm

This receiver’s
remote control

Other remote
control

4 Press the corresponding button on the other remote control that is sending (teaching) the
signal to this receiver’s remote control.

If the LED lights for one second and continues to flash, the setting has been successfully completed.

! If the LED flashes for five seconds, it means the memory is full. See

Erasing all learnt settings that are in one

input function

on

page 73

to erase a programmed button you’re not using to free up more memory (note that

some signals may take more memory than others).

! Note that interference from TVs or other devices will sometimes result in the remote control learning the

wrong signal.

! Some commands from other remote controls cannot be learned, but in most cases the remotes just need to

be moved closer together or farther apart.

5 To program additional signals for the current component repeat steps 3 and 4.

To program signals for another component, exit and repeat steps 2 through 4.

6 Press RCU SETUP to exit the programming mode.

Erasing one of the remote control button settings

This erases one of the buttons you have programmed and restores the button to the factory default.

1 Press and hold RCU SETUP, then press ‘7’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To erase operations registered at the TV CONTROL buttons, proceed to step 3.
! To cancel the preset setup mode press RCU SETUP.

2 Press the input function button corresponding to the command to be erased.

The LED flashes once.

3 Press and hold the button to be erased for three seconds.

If the LED lights for one second, the erasing has been successfully completed.

4 Repeat step 3 to erase other buttons.
5 Press RCU SETUP to exit the erasing mode.

Advertising
This manual is related to the following products: