Pioneer VSX-D810S - Manual (Page 39)

39
En
Controlling the Rest of Your System
MEMO:
• Some commands from other remote controls cannot
be learned, but in most cases the remotes just need to
be moved closer together or farther apart.
• Certain buttons represent modes that cannot be
learned from other remote controls. These include:
RCV, CH SELECT, CH LEVEL, FUNCTION
LOUDNESS, FL DIMMER, MUTING and MASTER
VOLUME.
• TV CONTROL buttons ( TV , VOL +/
−, and
TV
FUNC ) can only be learned in TV & TVC mode.
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two
seconds.
To cancel the SETUP mode at any time
Press
SETUP .
The remote control will also return to the previous
mode after thirty seconds of inactivity.
2 Press the MULTI CONTROL button for the
component you want to control
3 Press and hold the RECEIVER button for
two seconds to start the LEARNING mode.
The LED lights steadily.
To cancel LEARNING setup mode
Press
SETUP for one second.
If no commands are entered within thirty seconds the
remote will revert to its previous mode.
4 Point the two remote controls towards each
other. Press the button to be learned on this
receiver’s remote control (for example the
3
[play] button).
Point the remote controls directly at each other, about
2
−5 cm apart, and press the button on the remote
control for the operation you want to program. The
LED flashes rapidly.
5 Press the corresponding button on the other
remote control to be taught to this receiver’s
remote control (in the above example the
3
[play] button).
Point the remote controls toward each other.
Press the button on the other remote control
corresponding to the operation you wish to program.
The LED on this receiver’s remote will go out and
then resume a steady light if the operation is learned.
If the operation hasn’t been learned for some reason
the LED will blink for three seconds and then light
steadily. If this happens press the teaching key
repeatedly, varying the distances between the
remotes, until you see the LED on this unit’s remote
light steadily, without blinking first.
To program additional operations for the current
component
Repeat steps 4 and 5.
To program operations for another component
Repeat steps 2 through 5.
6 Press and hold SETUP for one second to exit
the LEARNING setup mode.
After thirty seconds of inactivity the remote control
will automatically leave the LEARNING mode and
revert to its previous mode.
Erasing One of the Learning
Remote Control Button Settings
This erases one of the buttons you have programmed
and restores the factory installed preset to that button.
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two
seconds.
2 Press the MULTI CONTROL button relating to
the function of the button to be cleared.
The remote control will return to the previous mode
after thirty seconds of inactivity.
3 Press the RECEIVER button twice within
three seconds to start erase mode.
The LED blinks.
4 Press the button to be cleared for three
seconds.
The LED lights steadily for three seconds and then
goes off.
5 Repeat step 4 to erase other codes.
6 Press and hold the SETUP button for one
second to exit the erase mode.
2
−
5 cm
TV TVFUNC MENU
VOLUME
MASTER VOLUME
TV CONTROL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
CHANNEL ENTER
DISC
MPX
DISPLAY
R F ATT
D.ACCESS
ST
TUNE TUNE
ST
CLASS
AT T
BAND /DTS
DSP
TEST T
O NE
CH SELECT
CH LEVEL
FUNCTION SIGNAL
SELECT
1¡
4
¢
7
8
3
¶
EFFECT
DVD
VCR
CD-R
TV
RCV
TUN
TVC
CD
MIDNIGHT
LOUDNESS
MUTING
SETUP
FL DIMMER MUL T I CONTROL 5.1 / 7.1
RECEIVER
SOURCE 1
2
3
4
5
6
7
8
10
9
0
2