B&K CT600 - Manual (Page 18)

Keypad Connections
Keypads connect to the CT Receiver at the Control Terminals. There is a five position phoenix terminal for
each of the hardware Zones labeled A-F on the six zone receiver and A-C on the three zone receiver.
Termination of the Keypad cables to the Control Terminals can be done in one of two ways:
Strip the keypad cable and terminate five wires to the five terminals of each Zone. If you are using a CAT 5
cable connected to an RJ-45 at the Keypad, there are extra connections for Ground,12V and IR data, (identi-
fied by the colors in parenthesis) to utilize the 4 twisted pair. These can be left un-terminated however for
maximum signal strength they should be connected. It is not important which wiring standard is used, (CAT5
A or CAT5 B), however the T568B is illustrated here:
CK1.2 Keypad Connections
B K
&
S B
I M P LY E T T E R !
14
A/V S OURCE INPUTS
CAUTION
RISK OF ELECTRIC SHOCK DO NOT O PEN RISK OF ELECTRIC SHOCK DO NOT OPEN
B&K Components, Ltd.
Made in the U.S.A.
B&K Components, Ltd.
Made in the U.S.A.
www.bkcomp.com
IN
1
IN
1
BUFFERED A /V SOURCE OUTPUTS ZONE LINE O UTPUTS
VOLTAGE
FM
ANTENNA
FM
ANTENNA
RF REMOTE IN
IN
2
IN
2
IN
3
IN
3
OUT
1
OUT
1
OUT
2
OUT
2
OUT
3
OUT
3
IN
4
IN
4
IN
5
IN
5
IN
6
IN
6
OUT
4
OUT
4
OUT
5
OUT
5
OUT
6
OUT
6
IN
7
IN
7
IN
8
IN
8
IN
9
IN
9
OUT
7
OUT
7
OUT
8
OUT
8
OUT
9
OUT
9
IR 1 IR 2 IR 3 IR 4 IR 5 IR 6 IR 7 IR 8
IN
A
IN
A
IN
B
IN
B
IN
C
IN
C
OUT
A
OUT
A
OUT
B
OUT
B
OUT
C
OUT
C
IN
D
IN
D
IN
E
IN
E
IN
F
IN
F
OUT
D
OUT
D
OUT
E
OUT
E
OUT
F
OUT
F
IR 9 AM ANTENNA
AC LINE
~
FUSE
CAUTION: F OR CONTINUED
PROT ECTION A GAINST RISK
OF FIRE REPLACE O NLY W ITH
SAME TYPE AND VALUE FUSE CAUTION: F OR CONTINUED
PROT ECTION A GAINST RISK
OF FIRE REPLACE O NLY W ITH
SAME TYPE AND VALUE FUSE
ZB ZE +12V
GND
RS232 XMIT
CTRL OUT
DATA IN
ZC ZF +12V
GND
RS232 XMIT
CTRL OUT
DATA IN
CONTROL
ZA ZD +12V
GND
RS232 XMIT
DATA IN
CTRL OUT
RIGHT LEFT
+ - + -
ZONE F
RIGHT LEFT
+ - + -
ZONE E
RIGHT LEFT
+ - + -
ZONE D
RIGHT LEFT
+ - + -
ZONE C
RIGHT LEFT
+ - + -
ZONE B
RIGHT LEFT
+ - + -
ZONE A
SPEAKER OUTPUTS
ARE 4 OHM STABLE
SPEAKER OUTPUTS
ARE 4 OHM STABLE
21
RS232
12V
GND
IN - IN -
OUT
IN +
12V
GND
IN - IN -
OUT
IN +
COMMON
CTRL I/O COMMON
CTRL I/O
OUT
BK &
SB IMPLY ETTER!
A
IT
First Color is Primary Color (Secondary)
IR OUTPUT - Solid Orange
GROUND - Green / White Stripe & (Solid Green)
RS232 XMIT - White / Blue Stripe
+12V - Orange / White Stripe & (Solid Brown)
Using a EIA-T568B Cat-5 Cable
RJ45 termination on one end
and bare wire on the other
CK1.2 Keypad Connection
Plug the male RJ45 connector into the
port on the CK1.2 Keypad. Additional
keypads in a zone can be run out of the Slave [OUT].
Master
[IN] RJ45
CT610/600/310/300 Connection
Insert and tighten the wires into the specific
Control I/O Port Phoenix
plug of the Zone that you wish to control.
Hardware Zone
Example connection of a CK1.2 Keypad
12V Control - White / Brown Stripe
Solid Blue = N/C