Pioneer CDJ-100S - Manual (Page 15)

15
<DRB1232>
En
OTHERS: TROUBLESHOOTING
Symptom
When the auto cue function is
set ON, track search is not fin-
ished.
Back cue function cannot be
carried out even though the
CUE button is pressed in play-
back mode.
DJ mode doesn't work.
The picture of the TV screen is
fluctuated or FM broadcast is
interfered with noise.
The disc is not rotating when
power is ON.
Remedy
÷ Press TIME MODE/AUTO CUE button for
more than 1 second to set the auto cue
function OFF.
÷ Set the cue point. (See page 10.)
÷ Set DIGITAL OUT switch to OFF.
÷ Turn off POWER of the player, or move
the player away from the TV or tuner.
÷ Playback can be started by pressing the
PLAY/PAUSE button. Press the EJECT
button to eject the disc.
Cause
÷ If the sound muted portion between
selections is long, searching time will
be long.
÷ If the sound muted portion is re-
corded for about 20 seconds or more,
playback will start without the auto
cue function.
÷ The cue point is not set yet.
÷ DIGITAL OUT switch is set to ON (dig-
ital output is effective).
÷ Interference is being picked up from
the CD player.
÷ The disc rotation stops automatically
if no operation has been performed
for 80 minutes or more in pause
mode.
¶ Static electricity and other external effects may cause this unit to malfunction. In this case, set the power switch to
OFF, then switch it on again after the disc has come to a complete stop.
¶ This unit cannot playback non-finalized CD-R discs (partial discs).
¶ This component is designed to play both ordinary 12 cm (5-inch) discs and 8 cm (3-inch) discs mounted on adapters.
Non-round (eccentrically shaped discs) cannot be played, since damage or malfunction may result.
Error display
When the player detects an error during operation, if will immediately stop and display an error code in the display window. Check the
error code with those listed in the table below to determine the cause of error. Contact your nearest Pioneer authorized service center
if the cause of the error is unknown, too difficult to fix or if the same error code continues to display after the remedy has been tried.
Refer to the error code when speaking to the Pioneer service representative.
Displayed error
code number
E-72 01
E-72 02
E-83 01
E-83 02
E-91 01
E-91 03
Type of error
TOC READ ERROR
FG PULSE ERROR
PLAYER ERROR
PLAYER ERROR
MECHANICAL TIME OUT
MECHANICAL TIME OUT
Error contents
TOC date cannot be read after 20 seconds.
Disc is rotating, but rotation cannot be ascer-
tained.
Disc loaded cannot be played properly.
Disc loaded cannot be played properly.
Mechanical operation did not end in allotted
time.
Mechanical operation did not end in allotted
time.
Possible Cause = Remedy
Disc has scratch
= Replace disc
Disc is dirty
= Clean disc
Foreign object is in disc com-
partment slot.
= Remove it.
300 Allstate Parkway
Markham, ON L3R 0P2
(905) 479-4411
For warranty information please see the Limited
Warranty sheet included with your product.
Should this product require service in Canada, please con-
tact a Pioneer Canadian Authorized Dealer to locate the
nearest Pioneer Authorized Service Company in Canada.
Alternatively, please contact the Customer Service Depart-
ment at the following address:
Pioneer Electronics of Canada, Inc.
Should this product require service in the U.S.A. and you
wish to locate the nearest Pioneer Authorized Independent
Service Company, or if you wish to purchase replacement
parts, operating instructions, service manuals, or
accessories, please call the number shown below.
800 – 872 – 4159
Please do not ship your product to Pioneer without first
calling the Customer Service Department at the above
listed number for assistance.
PIONEER ELECTRONICS SERVICE, INC.
CUSTOMER SUPPORT DIVISION
P.O. BOX 1760, LONG BEACH,
CA 90801-1760, U.S.A.
For warranty information please see the Limited Warranty
sheet included with your product.