Pioneer CDJ-100S - Manual (Page 8)

8
<DRB1232>
En
BEFORE OPERATIONS: PANEL FACILITIES
7 Playback address display
The elapsed playback time or remaining playback
time of the track playing is roughly indicated with
the full-scaled bar graph.
÷ When no disc is in the
disc compartment ................................................ off
÷ When displaying elapsed
playback time .............. lights up from the left side
÷ When displaying remaining
playback time .............. turns off from the left side
÷ When remaining playback time is
less than 30 seconds ..................................... blinks
8 WAH indicator
Lights or blinks when WAH function is active.
] P. 11
9 Pause indicator ( *)
Blinks during pause mode.
0 ZIP indicator
Lights or blinks when ZIP function is active. ] P. 11
- JET indicator
Lights or blinks when JET function is active.
] P. 11
= Play indicator ( #)
Lights during playback.
6 A.CUE indicator
Lights when the AUTO CUE function is used.
DISC LOADING/UNLOADING
3. Press the EJECT button to remove discs.
¶ When the EJECT button is pressed, disc rotation
stops and the disc is ejected from the loading slot.
¶ If the disc fails to be ejected when the EJECT but-
ton is pressed, the accessory forced eject pin can
be inserted into the front-panel's forced eject hole
to eject the disc.
] P. 4
CAUTION
Do not attempt to press a disc back into the slot when the
EJECT indicator appears. Pressing a disc back into the slot
while the EJECT indicator appears may cause the player
to stop. In this case, press the EJECT button again and
wait until the EJECT indicator goes out before reinserting
the disc.
Display Window
1 TRACK number display
Displays the current number of the track playing.
2 CUE indicator
Flashes when it is possible to input cue point, and
lights steadily after the completion of input.
3 Time display (REMAIN)
The elapsed playback time of the track being played
(when the REMAIN indicator is off) or the remaining
playback time of the track being played (when the
REMAIN indicator is on) is displayed in minutes (M)
and seconds (S), or frames (F).
4 Playback tempo display
Tempo changes made with the TEMPO control knob
are performed in 0.1% steps in the ±10% range. 0 to
+10% in the +10% to –16% range is indicated in 0.1%
steps and 0.2% steps from 0 to –16%.
5 MT indicator
Lights when the MASTER TEMPO function is used.
Label surface up
Insert straight
1. Set the rear-panel power switch to ON.
2. Insert a disc.
¶ Hold the disc with label surface upwards, and in-
sert into the front panel disc loading slot .
¶ When playing an 8 cm (3-inch) disc, place the disc
in a commercially available CD adapter before in-
serting in the loading slot.
¶ Only one disc can be loaded at a time. Never at-
tempt to load more than one disc at the same time,
or attempt to load a second disc when one disc
has already been loaded.
¶ When loading a disc, do not placing any twisting
force on the disc, or try to force the disc into the
slot. Also, do not attempt to interrupt or defeat
the motion of the disc when the player begins to
draw a disc into the slot or to eject a disc, since
damage to the disc or player could occur.
Do not force a disc into the unit when the power switch is
set to OFF as this may damage the disc and the unit.
PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3-
inch Discs)
1 When playing CD singles (8 cm/3-inch discs), al-
ways use the adapter for 8 cm/3-inch discs. Be-
fore loading the disc into the CD player, be sure to
check that it is secured properly by the catches of
the adapter. If discs have been inserted without
the adapter by mistake, remove the disc immedi-
ately by pressing the eject button. If the disc does
not come out with one press, press another time.
2 Use 8 cm/3-inch disc adapters labeled with the
'
mark (recommended standard product). Do
not use adapters which cause the disc to idle, nor
adapters which are bent or curved.