Toshiba RDXV49 - Manual (Page 21)

21 EN
In
tr
od
uct
ion
Con
n
ec
ti
on
s
Basi
c Se
tu
p /
TV
Vi
ew
Op
eration
P
lay
b
a
ck
E
d
it
in
g
O
th
e
rs
Fu
nct
ion
S
e
tu
p
Re
co
rd
in
g
V
H
S
Fu
nc
ti
on
s
Channel Setting
You can retune this unit or edit the channel setting with
following methods.
Programme the tuner to scan both analogue and DVB
channels you can receive in your area.
1
In stop mode, press [SETUP]. Select “General
Setting” using [K
\ L], then press [ENTER\OK].
“General Setting” menu will appear.
2
Select “Channel” using [K \ L], then press
[ENTER
\OK].
3
Select “Auto Tuning (DVB & ANALOG)” using
[K
\ L], then press [ENTER\OK].
The unit will start storing channels available in your area.
Wait for several minutes to finish channel storing.
4
Press [SETUP] to exit.
You can select only the channels memorised in this unit
by using [PROG.
G \ H].
To cancel auto tuning
Press [SETUP] during scanning.
Note
• The number of TV channels you can get is different depends
on your local area.
• If the auto tuning is cancelled during scanning, some
channels not yet tuned may not be received.
Programme the tuner to scan only the analogue channels you
can receive in your area.
1
In stop mode, press [SETUP]. Select “General
Setting” using [K
\ L], then press [ENTER\OK].
2
Select “Channel” using [K \ L], then press
[ENTER \OK].
3
Select “ANALOG Channel Setup” using [K \ L],
then press [ENTER \OK].
4
Select “Auto Tuning” using [K
\ L], then press
[ENTER \OK].
The unit will start storing channels available in your area.
Wait for several minutes to finish channel storing.
5
Press [SETUP] to exit.
You can select only the channels memorised in this unit
by using [PROG.
G \ H].
To cancel auto tuning
Press [SETUP] during scanning.
Note
• The number of TV channels you can get is different depends
on your local area.
• If the auto tuning is cancelled during scanning, some
channels not yet tuned may not be received.
• When “Country” setting is set to “France”, sorting of TV
channels from 1 to 6 will be performed automatically as
follows.
You can preset an analogue channel manually and
individually.
1
In stop mode, press [SETUP]. Select “General
Setting” using [K
\ L], then press [ENTER\OK].
2
Select “Channel” using [K \ L], then press
[ENTER
\OK].
3
Select “ANALOG Channel Setup” using [K \ L],
then press [ENTER
\OK].
4
Select “Manual Tuning” using [K \ L], then
press [ENTER
\OK].
5
Select “Position” using [K \ L], then press [B].
6
Select the position number you want to use
using [the Number buttons] or [K
\ L], then
press [{].
• You can select position number 1-99.
• With [the Number buttons], you only need to enter the
last 2-digit numbers.
7
Select “System” using [K \ L], then press [B].
8
Select “L” or “BG” using [K
\ L], then press
[{].
• If your system is SECAM-L, select “L”.
• If your system is PAL-B/G, select “BG”.
Auto Tuning (DVB & ANALOG)
DVB ANALOG
Auto Tuning (ANALOG)
ANALOG
General Setting
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
DVB Setting
Country
Auto Tuning (DVB & ANALOG)
DVB Channel Setup
ANALOG Channel Setup
Reset All
1: TF1 2: F2 3: F3
4: CANAL+ 5: F5/ARTE 6: M6
Manual Tuning (ANALOG)
ANALOG
!.!,/'
!UTO
Position
System
Channel
Decoder
Skip 1
L
1
OFF
ON
E3TK0FD_EN.book Page 21 Monday, March 9, 2009 10:00 AM