Liebherr WTEes 2053 Vinidor - Manual (Page 4)

4 Putting into operation
4.1 Transporting the appliance
CAUTION
Risk of injury and danger of damage as a result of incorrect
transport!
u Transport the appliance in a packed condition.
u Transport the appliance upright.
u Do not transport the appliance without assistance.
WARNING
Risk of injury due to broken glass!
In case of transport at an altitude of over 1500 m the glass
panes of the door may break. The fragments have sharp edges
and may cause serious injury.
u Take appropriate protective action.
NOTICE
Risk of damage to the door!
The glass door is heavy. If insufficiently secured, the hinges
and door may suffer damage.
u Transport the appliance only with shipping braces in place.
4.2 Installing the appliance
WARNING
Risk of fire due to short circuit!
If the mains cable/connector of the appliance or of another
appliance touch the rear of the appliance, the mains cable/
connector may be damaged by the appliance vibrations,
leading to a short circuit.
u Stand the appliance so that it is not touched by connectors
or main cables.
u Do not plug the appliance or any others into sockets located
near the rear of the appliance.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
u Only use the appliance when it is installed.
WARNING
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flam-
mable. Escaping refrigerant may ignite.
u Do not damage the piping of the refrigeration circuit.
WARNING
Fire hazard and danger of damage!
u Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
q In the event that the appliance is damaged, contact the
supplier immediately before connecting to the mains.
q The floor at the site must be flat and level.
q Do not install the appliance in a location where it is exposed
to direct radiation of the sun, next to a cooker, heater and
similar.
q Do not install the appliance without assistance.
q
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m 2 per 8 g of R
600a refrigerant used in the appliance. If the room in which
the appliance is installed is too small, a flammable gas-air
mixture may form in the event of a leakage in the refrigera-
tion circuit. The quantity of refrigerant used in your appliance
is indicated on the type plate on the inside of the appliance.
q Fit the appliance in stable kitchen units only.
q The following ventilation gaps must be observed:
• The depth of the ventilation channel at the rear of the unit
must be at least 38 mm.
• There must be a ventilation space of at least 200 cm 2 in
the plinth and at the top of the unit.
• Basically the principle applies: the larger the ventilation
space, the more energy-saving the appliance is in opera-
tion.
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u Remove the protective film from the outside of the appli-
ance.
u Remove all transit supports.
u Dispose of packaging material (see 4.5) .
Note
u Clean the appliance (see 6.2) .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.
4.3 Changing over the door hinges
Ensure that the following tools are to hand:
q Flat-blade screwdriver
q
Pliers
q Crosstip screwdriver
q • Torx screwdriver 15
• Torx screwdriver 20
• Torx screwdriver 25
Turn in the adjustable-height feet all the way.
Pull out the plug.
Open the door.
Putting into operation
4