1removing the door and soft stop mechanism, 2transferring the bearing parts, Putting into operation – Liebherr WTEes 2053 Vinidor User Manual
Page 5
![background image](/manuals/520382/5/background.png)
WARNING
Risk of injury and damage due to broken glass!
The glass door is heavy. If it drops, the glass pane may shatter.
u
Safeguard the door properly when it is removed!
u
Detachment of the door has to be carried out by two
persons.
u
Lay down the door on a soft mat.
4.3.1 Removing the door and soft stop mecha-
nism
Fig. 3
u
Lift off cover
Fig. 3 (1)
and cover
Fig. 3 (2)
as well as stopper
Fig. 3 (3)
.
u
Push cover of soft stop mechanism
Fig. 3 (4)
back and
detach it.
CAUTION
Danger of injury by the soft stop mechanism!
If the soft stop mechanism contracts and strikes the appliance,
fingers may get caught and the appliance may be damaged.
u
Keep a firm hold on the soft stop mechanism.
u
Lift the soft stop mechanism
Fig. 4 (5)
off the ball journal
Fig. 4 (6)
. Carefully
lift the spring using a screwdriver in
order to detach the spring clip
Fig. 4 (7)
. *
u
Carefully swivel the soft stop mecha-
nism to the appliance.
Fig. 4
u
Carefully lift the cover of
the turn hinge
Fig. 5 (8)
using a screwdriver and
slide it forwards.
u
Set the soft stop mecha-
nism at an angle away
from the appliance and
remove
the
cover
Fig. 5 (8)
.
Fig. 5
u
Unscrew the front screw
Fig. 6 (10)
from the
bearing of the soft stop
mechanism
Fig. 6 (11)
.
Fig. 6
CAUTION
Danger of injury due to the spring tension acting on the soft
stop mechanism.
u
Secure the soft stop mechanism.
u
Set the soft stop mecha-
nism
Fig. 7 (5)
at an angle
and carefully lay it on the
front face of the appliance.
u
Unscrew the middle screw
Fig. 7 (12)
from the bearing
of the soft stop mechanism
Fig. 7 (11)
.
u
Remove the soft stop
mechanism and set it
aside.
Fig. 7
u
To
detach
the
stop
Fig. 8 (13)
: undo the screw
Fig. 8 (14)
.
Fig. 8
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
To unscrew the top turn
hinge
Fig. 9 (9)
: undo the
screw
Fig. 9 (15)
.
Fig. 9
u
At the bottom, lift the
door
off
the
pin
Fig. 10 (16)
of the lower
turn hinge
Fig. 10 (17)
and set it aside.
u
Transfer the bearing pin
Fig. 10 (16)
in the turn
hinge and screw it firmly
into place (with 4 Nm).
Fig. 10
If the handle is already fastened:
u
detach the handle.
4.3.2 Transferring the bearing parts
u
To raise the bearing pin
Fig. 11 (18)
: Move turn
hinge
Fig. 11 (9)
up and
down.
u
Using pliers, pull out the
bearing pin
Fig. 11 (18)
and
set it aside.
Fig. 11
u
Transfer
the
stop
Fig. 12 (13)
to the oppo-
site side and screw it
firmly into place (with
2 Nm).
Fig. 12
u
Check whether there is a white plastic sleeve in the door
bearing on the opposite side. If not*: Draw the plastic sleeve
Fig. 12 (19)
out of the door bearing and insert it snugly at the
opposite side.
Putting into operation
5