Liebherr UIK 1550 Premium - Manual (Page 10)

4.6 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
u Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
WARNING
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u Check the electrical connection.
u Plug in the power plug.
4.7 Switching on the appliance
u Open the door.
u Press On/Off button Fig. 2 (1) .
w The appliance is switched on. The temperature display indi-
cates the set temperature.
w If all LEDs in the temperature display light up, demo mode is
activated. Please contact the after sales service.
5 Control
5.1 Food refrigeration
Note
u The maximum weight you can store in the pull-out compart-
ment with bottle rack and vegetable bin is 20 kg.
u Store readily perishable food such as pre-cooked meals,
meat and sausage products in the middle area of the coldest
zone. Store butter and preserves in the top area. (see Appli-
ance at a glance)
u Use recyclable plastic, metal, aluminium and glass
containers and cling film for wrapping.
u Do not store food too close together to enable good air
circulation.
5.2 Setting the temperature
The temperature depends on the following factors:
- the door opening frequency
- the room temperature at the site where the appliance is
installed
- the type, temperature and quantity of frozen food
Temperature setting to be recommended: 5 °C
u To access temperature adjustment: press the setting button
Fig. 2 (2) once.
w The LED of the current temperature flashes in the tempera-
ture display.
u Press the setting button Fig. 2 (2) the number of times
needed until the required temperature shines in the LED
display.
Note
u Long pressing of the setting button sets a slightly colder
value within a small temperature range (e.g.: between 5 °C
and 7 °C). The LED of the next lower temperature range
then shines in the temperature display.
5.3 SuperCool
With SuperCool you switch to the highest cooling
performance to reach lower cooling temperatures.
Use SuperCool, to rapidly cool large amounts of
food.
When SuperCool is activated, the appliance operates with
maximum cooling performance. The noise of the refrigeration
unit may be temporarily louder as a result.
The SuperCool function uses slightly more energy.
5.3.1 Cooling with SuperCool
u Briefly press SuperCool button Fig. 2 (4) .
w The SuperCool button Fig. 2 (4) lights up.
w The cooling temperature drops to the coldest value.
SuperCool is activated.
w SuperCool is automatically deactivated after 6 to12 hours
The appliance continues to operate in the energy-saving,
normal mode.
5.3.2 To prematurely deactivate SuperCool
u Briefly press SuperCool button Fig. 2 (4) .
w The SuperCool button Fig. 2 (4) goes out.
w SuperCool is deactivated.
5.4 Relocating the retainers
Fig. 24
u Take hold of the retainers at the right and left, carefully lift
them out and press them into the new seats until the holders
engage.
5.5 Partitioning the vegetable bin
Fig. 25
u The partition can be used to subdivide the vegetable bin.
Insert the partition at the guides or simply lift it out.
Control
10 * Depending on model and options