Philips 46PFL3708-F7 - Manual (Page 24)

24 English
Before you begin:
You must set Home in Location. ➟ p.31
Otherwise, personalized Picture and Sound settings will not be
memorized after the unit goes into Standby mode.
1
Press and use ▲▼ to select Sound, then press OK.
2
Use ▲▼◄► to select the item you want to adjust, then press OK.
Adjust the tonal quality for each frequency.
This selects sound modes for more spatial or surround sound reproduction.
Incredible Surround gives you the stereophonic virtual space through
your existing 2-channel stereo system.
* This part differs depending on the product you have.
• SRS TruSurround XT for 40PFL4708, 39PFL2708, 32PFL3508, 32PFL4508,
29PFL4508, 24PFL4508.
• Incredible Surround for 50PFL3708, 46PFL3708, 40PFL1708.
This function keeps a constant loudness differential between the TV
commercials and the programs.
You can select the Audio Output from the unit’s speakers or not. If your
amplifier is HDMI link function compatible and connected by an HDMI
cable to this unit, some sound operations such as volume up can be
changed by using this unit’s remote control.
You can select audio output through a digital audio output connector.
You can set the output mode as a default for the sound mode (Analog
TV only).
This setting is not interlocked when you change the output mode by
pressing SAP. Refer to Switching audio mode.
➟ p.19
Before you begin:
Make sure the unit is connected to antenna or cable.
1
Press and use ▲▼ to select Setup, then press OK.
2
Adjust the following items.
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are
registered with your cable TV provider when you install Cable channels.
1
Use ▲▼ to select Autoprogram, then press OK.
• If you run Autoprogram when you have locked channels, a
message appears asking to enter your PIN. Enter your PIN in
order to complete the installation. You need to set the channel
lock again after the installation.
2
Use ▲▼ to select an appropriate option, then press OK.
– When Antenna is selected, the TV detects any off-the-air
antenna signals. It searches for ATSC (Digital) and NTSC
(Analog) channels available in your area.
– When Cable is selected, the TV detects signals supplied by cable.
It searches for DTV, Analog TV and Cable channels available in
your area.
Continued on next page.
Auto sound
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music and News)
When you adjust the following settings (Equalizer, SRS
TruSurround XT*, Incredible Surround* and Auto volume
leveling), Personal sound will be set automatically.
Equalizer
Cursor ◄ Cursor ►
to adjust each level of tonal quality
Press BACK to go back to the previous menu.
*SRS
TruSurround XT
Off to set SRS TruSurround XT ® to Off
On
to set SRS TruSurround XT ® to On
*Incredible
Surround
Off Natural effect.
On Emphasized effect.
Auto volume
leveling
Off to remove the auto volume leveling
On
to reduce volume differences between
the TV commercials and the programs
TV speakers
On to output sound from the unit’s speakers
Off
not to output sound from the unit’s
speakers
Speakers
EasyLink
to control Audio Output from your
connected EasyLink Compliant Devices
with VOL + / − by using this unit's
remote control.
Digital output
format
Multichannel
to output multichannel signals.
(When the audio of the content is PCM,
it will be output in PCM even if
Multichannel is selected.)
PCM to output PCM signals.
Sound
Picture
Sound
Setup
Features
Language
USB
Auto sound
Equalizer
SRS TruSurround XT
Auto volume leveling
TV speakers
Standard
On
Off
On
Digital output format
Audio setting
Multichannel
Stereo
*
Audio setting
Stereo to output stereo-audio
Mono to output mono-audio
SAP to output second audio program
Setup
Picture
Sound
Setup
Features
Language
USB
Autoprogram
Channel list
Add channels
Antenna
Cable Or
Picture
Sound
Setup
Features
Language
USB
Antenna
Back
Cable
Antenna
Cable
Autoprogram will rescan all channels.
Auto programming may take more than 20
minutes to complete.
Select your signal source.
ANTENNA IN