Fluid Management Dual-Pump Harbil - Manual (Page 12)

10
15
HARBIL DUAL PUMP COWR DISPENSER
MAINTENANCE
1. DAILY MAINTENANCE
Agitate the colorants as required every morning. The actual amount of agitation
time can be determined by your own experience with the colorants. On dispensers
equipped with manual agitation this would normally be about ten to fifteen turns
of the agitator knob every morning, although this may vary from colorant to
colorant. Dispensers equipped with motorized agitation would normally be run
for approximately fifteen to thirty minutes.
Check the level of the colorant in all of the canisters and if the colorant level is
down to one-half of the lower agitation blade, add a minimum of two quarts of
colorant. The correct operating amount of colorant in each canister should be
from one-half quart to six quarts.
Wipe all of the nozzles clean with either water or mineral spirits, depending on
the type of colorant being used (DO NOT USE MINERAL SPIRITS FOR
WATER OR GLYCOL BASED COLORANTS, as this will cause damage to
the O-Rings on the Valve Assembly).
2. WEEKLY MAINTENANCE
Dispense a full measure of any colorant that has not been used during the week
into an empty receptacle and then pour it back into the canister (as described in
GENERAL INSTRUCTIONS-Section 5, AGITATING THE COLORANTS
on page 8).
3. GENERAL MAINTENANCE
IMPORTANT:
If the dispense nozzle of the pump should become clogged the insertion of a paper
clip or other similar object will clean out any obstruction in the nozzle. However,
before doing this, the DISPENSING VALVE LEVER MUST BE OPENED
(pulled forward) as in dispensing. BE SURE TO REMOVE the paper clip before
closing the valve lever.
If a col orant leak develops at the top of the dispensing pump or there is colorant
on the piston rod, a one ounce or five ounce Pump Repair Kit (part no. 4223112
and 4223502 respectively) should correct the problem. If after replacement of
the Pump Repair Kit the problem still persists, the inside walls of the pump
tube may be scored and the pump tube will have to be replaced.
It is recommended that one or two pump repair kits be kept in stock for
emergencies.
DUAL PUMP 192 OZ. CANISTER PUMP ASSEMBLY
ITEM PART NO. DESCRIPTION NO. REQ.
4209000 Canister Pump Assy. w/o Agitator & Cover.192 oz. U.S. 1
4209002 Canister Pump Assy. w/o Agitator & Cover.192 oz. Metric 1
4209003 Canister Pump Assy. w/o Agitator & Cover.192 oz. Imp. 1
4209060 Canister Pump Assy. w/o Agitator & Cover.192 oz. U.S. 1
6MM Exit Port
4219000 Canister Block & Sleeve Only,192 oz. 1
4219060 Canister Block & Sleeve Only.192 oz., 6MM Exit Port 1
1 4000008 Knob, Black, #25.5/16-24 TH 1
2 4228501 Knob, Black.#44.3/8-16 TH 1
3 4000018 Screw, Set, 8-32 x 3/16, Socket, C/P 5
4 4226- Gauge Assembly Complete.1 oz. 1
5 42265- Gauge Assembly Complete.5 oz. 1
6 4228100 Gasket, Pump Tube.1 oz. 1
7 4228502 Gasket, Pump Tube.5 oz. 1
8 4235004 Lever. Valve, 5 oz. 1
9 4235005 Pin, Roll, 1/8 x 1-1/2, SS 1
10 4235000 Valve, Lever Assembly Complete, 5 oz. 1
10 4235601 Valve, Lever Assembly Complete.5 oz. (6MM) 1
10 4235501 Valve & O' Ring Assembly.5 oz. (Viton) 1
10 4235507 Valve & O' Ring Assembly.5 oz. (Thiokol) 1
11 4235006 O' Ring, Valve, Viton.5 oz. 2
11 4235007 O' Ring, Valve, Thiokol, 5 oz. 2
12 4000061 Screw, PHCS.10-24 x 3/8 Slot, C/Z 1
13 4235013 Retainer, Valve, Lever. 5 oz. 1
14 4235011 Plunger Valve Stop 1
15 4000150 Nut, Hex.1/4-28.Jam 1
4000108 Nozzle, Cap and Pad 1
Kits
4290502 Kit. Canister Repair.5 oz.
• U.S.
4223502 Kit.Pump Repair.5 oz
•• U.S.
4223112 Kit.Pump Repair.1 oz •• U.S.
4235014 Kit. Valve Repair.5 oz .• Single Exit
4235015 Kit. Valve Repair.5 oz .• Double Exit