Installation instructions, General – L.B. White 350 Premier User Manual

Page 8

Advertising
background image

1. Read all safety precautions and follow L. B. White

recommendations when installing this heater. If

during the installation or relocating of heater, you

suspect that a part is damaged or defective, call a

qualified service agency for repair or replacement.

2. Make sure the heater is level and properly positioned

before use. Observe and obey all minimum safe

distances of the heater to the nearest combustible

materials. Safe distances are given on the heater

dataplate and on page 4 of this manual.

3. This heater may be installed either indoors or

outdoors. For outdoor installations, only the following

air distribution devices may be used:

-- 18 in. Dia. x 12 ft. duct:

L.B. White Part # 22841

-- End Diffuser: L.B. White Part # 23054

DO N

NOT U

USE AANY O

OTHER LLENGTH O

OF D

DUCTWORK O

OR

FIELD FFABRICATED D

DUCT, TTARPS, S

STOVE PPIPE, EETC.

ON TTHIS H

HEATER.

ATTENTION

When using the ducting, ensure that bends in duct are

kept to a minimum. A maximum of two 90º bends is

allowed.

Reducing the number of bends will ensure that the

warm air exiting the heater flows freely, thereby

preventing overheating. If there are excessive bends,

the high limit switches may open.

4. The heater’s gas pressure regulator (with pressure

relief valve) must be protected from adverse weather

conditions (rain, ice, snow) as well as from building

materials (tar, concrete, plaster, etc.) which can affect

safe operation and could result in property damage or

injury.

5. Heaters used in the vicinity of combustible tarpaulins,

canvas, plastics, wind barriers, or similar coverings

shall be located at least 10 feet from the coverings.

The coverings shall be securely fastened to prevent

ignition or upsetting of the heater due to wind action

on the covering or other material.

6. Check all connections for gas leaks using approved

gas leak detectors. Gas leak testing is performed as

follows:

-- Check all pipe connections, hose connections,

fittings and adapters upstream of the gas control

with approved gas leak detectors.

-- In the event a gas leak is detected, check the

components involved for cleanliness and proper

application of pipe compound before further

tightening.

-- Tighten the gas connections as necessary to stop

the leak.

-- After all connections are checked and any leaks

are stopped, turn on the main burner.

-- Stand clear while the main burner ignites to

prevent injury caused from hidden leaks that could

cause flashback.

-- With the main burner in operation, check all

connections, hose connections, fittings and joints

as well as the gas control valve inlet and outlet

connections with approved gas leak detectors.

-- If a leak is detected, check the components

nvolved for cleanliness in the thread areas and

proper application of pipe compound before

further tightening.

-- Tighten the gas connection as necessary to stop

the leak.

-- If necessary, replace the parts or components

involved if the leak cannot be stopped.

-- Ensure all gas leaks have been identified and

repaired before proceeding.

7. A qualified service agency must check for proper

operating gas pressure upon installation of the

heater.

WARNING

Fire aand EExplosion H

Hazard

C

Caann ccaauussee pprrooppeerrttyy ddaam

maaggee,, sseevveerree iinnjjuurryy oorr ddeeaatthh

1. To avoid dangerous accumulation of fuel gas, turn

off gas supply at the heater service valve before

starting installation, and perform gas leak test after

completion of installation.

2. Do not force the gas control knob. Use only your

hand to turn the gas control knob. Never use

any tools. If the knob will not operate by normal hand

pressure the gas control valve should be replaced by

a qualified service technician. Force or attempted

repair may result in fire or explosion.

7

Installation Instructions

GENERAL

WARNING

Fire aand EExplosion H

Hazard

Do not use open flame (matches, torches, candles,

etc.) in checking for gas leaks.

Use only approved leak detectors.

Failure to follow this warning can lead to fires or

explosions.

Fires or explosions can lead to property damage,

personal injury or death.

Advertising