Snorkel MHP34J(Bi-Energy Option) - Manual (Page 9)

1. Safety
■ Safe Operation
The following safety information is vitally important
for safe operation of the MHP12/34J. Failure to fol-
low these instructions can result in personal injury
or DEATH.
❑ Pre-start Inspection
At the start of each work shift, the MHP12/34J shall
be given a visual inspection and function test. See
the “Daily Inspection and Maintenance” chapter 7,
in this manual for a list of items to inspect and test.
DO NOT operate the MHP12/34J unless you
are trained and authorized, understand the
operation characteristics of the MHP12/34J,
and have inspected and tested all functions
to be sure they are in proper working order.
❑ Work Place Inspection and Practices
Do not use the MHP12/34J as a ground for welding.
Ground to the work piece.
Before the MHP12/34J is used, and during use,
check the area in which the MHP12/34J is to be
used for possible hazards such as, but not limited
to:
1. Drop-offs or holes.
2. Side slopes.
3. Bumps and floor obstructions.
4. Debris.
5. Overhead obstructions and electrical
conductors.
6. Hazardous locations.
7. Inadequate surface and support to withstand
all load forces imposed by the aerial platform
in all operating configurations.
8. Wind and weather conditions.
9. Presence of unauthorized persons.
10. Other possible unsafe conditions.
Before the MHP12/34J is used, determine the haz-
ard classification of any particular atmosphere or lo-
cation according to ANSI/NFPA 505-1987.
Any MHP12/34J operated in a hazardous location
must be approved and of the type required by
ANSI/NFPA 505-1987.
A recommended safety practice is to have
personnel that are trained in the operation of the
emergency controls working in the immediate area
of the MHP12/34J to assist the platform operator in
the event of an emergency.
When moving the platform, check the clearance
around the MHP12/34J to avoid contact with struc-
tures or other hazards. Always look in the direction
of motion.
Keep ground personnel from under the platform
when the platform is raised.
Secure all accessories, containers, tools, and other
materials in the platform to prevent them from acci-
dentally falling or being kicked off the platform.
DO NOT engage in any form of “horseplay” or “stunt
driving” while operating the MHP12/34J.
DO NOT permit riders on the machine anyplace
other than on the platform.
Remove all loose objects stored in or on the ma-
chine, particularly in the platform. Remove all ob-
jects which do not belong in or on the machine.
When other moving equipment is in the area, take
special precautions to comply with local regula-
tions regarding warnings.
Never steady the platform by positioning it against
another platform.
DO NOT operate an MHP12/34J that is not func-
tioning properly, or has been damaged, until the
machine has been repaired by a qualified mainte-
nance person.
DO NOT operate a MHP12/34J that does not have
all its decals and placards attached and legible.
Watch for bystanders and never allow anyone to be
under, or to reach through, the machine and its
equipment while operating.
Use the recommended transport device when
loading the machine.
❑ Electrocution
T h e M H P 1 2 / 3 4 J i s a n a l l m e t a l b o o m ,
NON-INSULATED, aerial work platform.
DO NOT operate it near ELECTRICAL conductors.
Regard all conductors as being energized.
DO NOT operate outside during a thunderstorm.
❑ Tipover and Falling Hazards
DO NOT operate the MHP12/34J from a position on
trucks, trailers, railway cars, floating vessels, scaf-
folds, or similar equipment unless the application is
approved in writing by Snorkel.
If the platform or elevating assembly becomes
caught, snagged, or otherwise prevented from
normal motion by an adjacent structure or other
obstacles such that control reversal does not free
the platform, remove all personnel from the
MHP12/34J – 11447A page 1 - 1
CAUTION