JLG G6-42A Operator Manual - Manual (Page 14)

9150-3102 REV. -
DECALS
2.2
9132-3030
NEVER OPERATE MACHINE WITHOUT
CONSULTING PROPER CAPACITY CHART FOR THE
CARRIAGE/FORK COMBINATION BEING USED.
R
9140-3618
FRONT
GENERAL NOTES
9140-3618
LEVEL GRADALL HANDLER BEFORE LIFTING ABOVE 4 FT.
USE CAPACITY CHART FOR SPECIFIC ATTACHMENT ON MACHINE.
FOR OTHER ATTACHMENTS CONSULT A GRADALL DEALER
FOR LOAD RATINGS NOT LISTED.
USE LARGEST NUMBER VISIBLE FROM THE CAB TO
DETERMINE BOOM EXTENSION.
MATCH WITH BOOM ANGLE TO DETERMINE ALLOWABLE LOAD.
FIGURES SHOWN ARE STACKING CAPACITY TRUCK LEVEL.
RATED LIFTING CAPACITIES SHOWN ARE WITH MACHINE ON A FIRM,
LEVEL SURFACE WITH UNDAMAGED, PROPERLY INFLATED TIRES.
MACHINE SPECIFICATIONS AND STABILITY ARE BASED ON RATED LIFT
CAPACITIES AT SPECIFIC BOOM ANGLES AND BOOM LENGTHS.
IF SPECIFICATIONS ARE CRITICAL, THE PROPOSED APPLICATION
SHOULD BE DISCUSSED WITH YOUR DEALER.
DO NOT EXCEED RATED LIFT CAPACITY LOADS, AS UNSTABLE AND
DANGEROUS MACHINE CONDITIONS WILL RESULT.
DO NOT TIP THE MACHINE FORWARD TO DETERMINE ALLOWABLE LOAD.
CERTAIN CARRIAGE/FORK COMBINATIONS MAY CAUSE HANDLER TO TIP
WITHOUT LOAD WHEN EXTENDED INTO "NO OPERATION" ZONE AS NOTED
ON CAPACITY CHART.
CAPACITY LIMITS FOR THIS UNIT ARE BASED IN
ACCORDANCE WITH STANDARDS LISTED ON SERIAL
NUMBER PLATE.
BACK
SAMPLE ONLY - USE CHART IN CAB
Located on dashboard
P/N 9140-3618
Located on dashboard
P/N 9147-3139
Located on right cab wall
P/N 9055-3028
Located on right cab wall
P/N 9150-3102
Located on right cab wall
and cab fender
P/N 9132-3030
8. ON INCLINES, TRAVEL WITH LOAD UP-GRADE.
9. DO NOT USE BOOM AS WALKWAY.
10. USE TWO HANDS WHEN CLIMBING ON MACHINE.
1. ONLY TRAINED AND AUTHORIZED PERSONNEL MAY
OPERATE THIS MACHINE.
2. BEFORE OPERATING, READ AND UNDERSTAND ALL CAPACITY
CHARTS, OPERATOR MANUALS AND SAFETY MANUALS. IF
MANUALS ARE NOT AVAILABLE, CONSULT AN AUTHORIZED
GRADALL DEALER. UNDERSTAND ALL CONTROLS IN CAB AND
CHECK FOR PROPER OPERATION. CLEAR LOOSE OBJECTS
OFF MACHINE AND SOUND HORN BEFORE STARTING ENGINE.
3. OPERATOR MUST BE SEATED WITH SEAT BELT FASTENED.
ASSURE FORWARD/REVERSE LEVER IS IN NEUTRAL,PARK
BRAKE APPLIED AND ALL HYDRAULIC CONTROLS ARE IN
NEUTRAL BEFORE IGNITION SWITCH IS TURNED ON.
4. DO NOT OPERATE MACHINE WITHOUT PROPER CAPACITY
CHART IN PLACE.
5. BEFORE MOVING, BE SURE OF A CLEAR PATH AND SOUND
HORN. WATCH FOR PEDESTRIANS AND OBSTRUCTIONS.
CHECK OVERHEAD AND SIDE CLEARANCES. ALWAYS LOOK
IN DIRECTION OF TRAVEL.
6. START, TURN, AND BRAKE SMOOTHLY. REDUCE TRAVEL
SPEEDS FOR TURNS, SLIPPERY, OR UNEVEN SURFACES.
AVOID RUNNING OVER LOOSE OBJECTS OR HOLES IN THE
ROADWAY SURFACE.
7. WHEN TRAVELING WITH LOAD, FULLY RETRACT BOOM AND
PLACE FORKS IN CARRY POSITION (APPROX.12" ABOVE
GROUND). TILT CARRIAGE BACK SLIGHTLY TO CRADLE
LOAD. USE EXTREME CAUTION WHEN TURNING.
11. USE ONLY A GRADALL MANUFACTURED PERSONNEL WORK
PLATFORM FOR LIFTING PERSONNEL. NO RIDERS ON MACHINE,
FORKS, LOAD, OR OTHER LIFTING ATTACHMENTS AT ANY
TIME. DO NOT USE PERSONNEL WORK PLATFORM WITHOUT THE
PROPER GRADALL MATERIAL HANDLER/PERSONNEL WORK
PLATFORM CAPACITY CHART DISPLAYED IN THE CAB. DO NOT
DRIVE MACHINE WITH PERSONNEL IN PLATFORM.
12. KEEP OTHERS AWAY FROM MACHINE WHILE OPERATING.
DO NOT STAND UNDER BOOM OR LOAD.
13. USE EXTREME CARE WHEN HANDLING LONG, HIGH, OR
WIDE LOADS. DO NOT HANDLE UNSTABLE OR LOOSELY
STACKED LOADS.
14. FORKS TO BE CENTERED UNDER LOAD AND SPACED APART
AS FAR AS POSSIBLE.
15. BEFORE ADJUSTING OR SERVICING, PLACE
FORWARD/REVERSE LEVER IN NEUTRAL, REST BOOM ON
GROUND OR SUPPORT, SET PARKING BRAKE, SHUT OFF
ENGINE AND CHOCK WHEELS.
16. BEFORE LEAVING MACHINE UNATTENDED, PLACE
FORWARD/REVERSE LEVER IN NEUTRAL, LOWER BOOM,
SET PARKING BRAKE,AND SHUT-OFF ENGINE. CHOCK
WHEELS IF MACHINE MUST PARK ON AN INCLINE.
17. LEVEL MACHINE BEFORE LIFTING ANY LOAD ABOVE 4
FEET. (IF EQUIPPED WITH FRAME LEVELING).
18. OPERATOR PROTECTION (SUCH AS HARD HATS, SAFETY
GLASSES, AND/OR HEARING PROTECTION) SHOULD BE
WORN WHEN JOB CONDITIONS WARRANT. ALWAYS USE
SEAT BELT.
19. IMPROPER USE OF MACHINE COULD RESULT IN MACHINE
TIPPING OVER. IF MACHINE STARTS TO TIP OVER, DO
NOT LEAVE OPERATORS SEAT. LEAN AWAY FROM TIP &
BRACE YOURSELF.
20. KEEP MIRROR(S) CLEAN AND PROPERLY ADJUSTED.
OBJECTS IN MIRROR ARE CLOSER THAN THEY APPEAR.
9055-3028 REV. A
FOR SAFE OPERATION OF MACHINE AND TO MINIMIZE RISK OF
SERIOUS INJURY, READ AND OBSERVE THE FOLLOWING:
48" & 72" SLOPE PILER
9147-3139 (-)
BACK
DEDUCT 350 LBS
FROM ALL CAPACITIES
WHEN MACHINE IS
EQUIPPED WITH WINCH
MODEL
G6-42A
USE WITH: 9140-5101 48"
9140-5079 72"
SLOPE PILER CARRIAGE
RATED CAPACITY 2 FT. LOAD CENTER
600 LBS
2000 LBS
3000 LBS
4000 LBS
5000 LBS
6600 LBS
0' 4' 8' 12' 16' 20' 24' 28' 32'
-8'
-4'
0'
4'
8'
-9°
0°
10°
20°
12'
16'
20'
30° 24'
28'
32'
36'
40'
44'
48'
40°
50°
60°
70°
6
5
4
3
2
1
USE WITH:
9140-5073 48" CARRIAGE
9140-5074 72" CARRIAGE
9140-5024 WINCH (4,000 LB MAX. CAPACITY)
6600 LBS
6000 LBS
5000 LBS
4000 LBS
3000 LBS
2000 LBS
1000 LBS
9147-3139 (-)
FRONT
48" & 72" CARRIAGES
MODEL
G6-42A
DEDUCT 350 LBS
FROM ALL CAPACITIES
WHEN MACHINE IS
EQUIPPED WITH WINCH
RATED CAPACITY 2 FT. LOAD CENTER
0°
10°
20°
30°
40°
50°
60°
70°
1
2
3
4
5
6
-9°
0'
-4'
-8'
4'
8'
12'
16'
20'
24'
28'
32'
36'
40'
44'
0' 4' 8' 12' 16' 20' 24' 28' 32'
48'
SAMPLE ONLY - USE CHART IN CAB