JLG G6-42A Operator Manual - Manual (Page 7)

Form No. 20036 • G6-42A Owner/Operator Manual
General
This Manual provides important information regarding safe operating and
maintenance requirements for GRADALL Material Handlers. Refer to front cover
for specific model and serial number range.
If you have any questions regarding the material handler, contact your GRADALL
Material Handler Distributor.
Operator Qualifications
Operators of the material handler must be in good physical and mental condition,
have normal reflexes and reaction time, good vision and depth perception and
normal hearing. He must not be using medication which could impair abilities
nor be under the influence of alcohol or any other intoxicant during the work
shift.
The operator should possess a valid, applicable driver’s license and must have
completed a training course for this type of material handling equipment.
In addition, the operator must read/view, understand and comply with
instructions contained in the following material furnished with the material
handler:
• This Owner/Operator Manual
• GRADALL Material Handler Safety Manual
• All instructional decals and plates
• Any optional equipment instructions furnished
The operator must also read, understand and comply with all applicable Employer,
Industry and Governmental rules, standards and regulations.
Orientation
When used to describe the location of components in the material handler, the
directions “front’”, “rear”, “right” and “left” relate to the orientation of a person
sitting in the operator’s seat. (See figure I-1)
Related Manuals & Decals
Separate publications are furnished with the material handler to provide
information concerning safety, replacement parts, maintenance procedures,
theory of operation and vendor components. Replacement manuals, decals and
instruction plates can be ordered from your GRADALL Material Handler Distributor.
Models Covered
This Manual covers basic information for Gradall Material Handlers. Detailed
information for each particular machine is in the maintenance section in the
back of this manual. Be certain to refer to proper information for your unit
and the optional equipment furnished on your machine.
Serial Number Location
Specify Model Number and Serial Number when ordering parts and when
discussing specific applications and procedures with your Distributor. The model/
serial number plate is located inside the operator’s cab, right wall.
(See figure I-2)
NOTE!
“Material handler” and handler
are used interchangeably
throughout this Manual.
Though no offense or
discrimination is intended, only
the masculine pronouns will be
used throughout the remainder
of this Manual.
NOTE!
REAR
FRONT
RIGHT
LEFT
Figure I-1
Figure I-2
INTRODUCTION
24" 24"
406 MILL AVE. S.W., NEW PHILADELPHIA, OHIO 44663
GRADALL IS A REGISTERED TRADEMARK FOR HYDRAULIC EQUIPMENT BUILT BY THE GRADALL CO. MANUFACTURED IN THE U.S.A.
AS RELEASED FROM FACTORY THIS TRUCK MEETS THE DESIGN SPECIFICATIONS ESTABLISHED IN AMERICAN NATIONAL STANDARDS FOR POWERED INDUSTRIAL TRUCKS PART III ASME B56.6b-1998.
CAP# X1000
A
B 42'
6.6 1.0
CAPACITY WITH STANDARD 48" & 72" CARRIAGE.
(WITHOUT ATTACHMENTS)
4.6'
B
C
A
D
20,650
20,460
24" 24"
42' 24"
C
D
ATTACHMENT TRUCK & ATTACHMENT WEIGHT
24"
D C B A
6.6 20,180
CAP# 1000
9147-3131 (B)
42' 24" 24"
6.6 20,290
6.6 42' 24" 24"
24" 24" 42' 6.6
48" CARRIAGE P/N 9140-5073 *
72" CARRIAGE
P/N 9140-5074 *
SHIPPED WITH
48" SLOPE PILER P/N 9140-5101 *
72" SLOPE PILER
P/N 9140-5079 *
2.0' 26.9'
2.0'
2.0'
2.7'
2.7'
FORKS RATED LESS THAN THE ATTACHMENT CAPACITY SHOWN ABOVE DECREASE CAPACITY OF ATTACHMENT TO THAT OF FORKS. FORKS RATED MORE THAN ATTACHMENT CAPACITY DO NOT INCREASE ATTACHMENT CAPACITY.
*WEIGHTS ARE BASED ON USING 2 X 4 X 48" FORKS (APPROX. 268# PER PAIR) **BUCKET DIMENSIONS (A & D) REFER TO BUCKET LIP HEIGHT. ***TRUSS BOOM & WINCH DIMENSIONS (A & D) REFER TO HOOK CENTER. ****WEIGHT IS BASED ON SP'L SWING MAST FORKS (APPROX. 230# PER PAIR) *****PLATFORM DIMENSIONS (A & D) REFER TO CENTER OF FLOOR.
19430 LBS
SAMPLE ONLY
In the U.S.A., the operator
must have completed a training
course meeting the OSHA
Powered Industrial Truck
Operator Training
Requirements (CFR 1910.178)
NOTE!