JLG 2658E3 ANSI Operator Manual - Manual (Page 57)

SECTION 4 - MACHINE OPERATION
3120761 – JLG Sizzor – 4-5
When equipped for 1,000 lb. (455 kg) platform
capacity, Model 2033E3 cuts out the DRIVE function
at a platform height of 17 feet (5.2 m) and Model
2646E3 cuts out the DRIVE function at a platform
height of 19 feet (5.8 m).
Traveling in Reverse
1. Position power selector switch at ground control sta-
tion to platform.
2. Position emergency stop switch at platform control
station to on position.
3. Press drive switch, in conjunction with the trigger
switch, and move joystick rearward (reverse) and
hold for duration of travel. Drive speed is determined
by the distance the joystick is moved from the center
off position. The drive switch is part of the enable cir-
cuit, which supplies power to the drive switch and
the joystick for 3 seconds after the drive switch is
pressed. If the joystick is not activated within 3 sec-
onds after the drive switch is pressed, power is
removed from the switch and joystick and the switch
must be pressed again before activating the joystick.
When the joystick is returned to the center off posi-
tion, the operator has 3 seconds to re-activate the
joystick or select another function before power is
removed by the enable circuit. DO NOT activate the
high drive speed switch when traveling in
reverse.
4.8 PARKING AND STOWING
NOTE: When parking battery-powered units overnight, bat-
teries should be charged in accordance with instruc-
tions in Section 2 to ensure readiness for the
following workday.
Park and stow machine as follows:
1. Drive machine to a reasonably well-protected and
well-ventilated area.
2. Ensure platform is fully lowered.
3. Position emergency stop switch to off position.
4. If necessary, cover the instruction placards, caution
and warning decals so that they will be protected
from hostile environment.
5. Chock at least two wheels when parking machine for
an extended period of time.
6. Turn switch to OFF and remove key to disable
machine from unauthorized use.
4.9 PLATFORM LOADING
The platform maximum rated load capacity is shown on a
placard located on the platform and is based upon the fol-
lowing criteria.
1. Machine is positioned on a smooth, firm and level
surface.
2. All braking devices are engaged.
3. Maximum platform capacity for each model in its
standard configuration is as follows:
1532E3 - 600 lb. (270 kg)
1932E3 - 500 lb. (230 kg)
2033E3/2646E3 - 750 lb. (340 kg)
2046E3/2658E3 - 1,000 lb. (450 kg)
4. Optional platform capacity for Models 2033E3 and
20646E3 is 1,000 lb. (450 kg).
5. If machine is equipped with the optional pipe racks,
the maximum capacity of the pipe racks is 100 lb.
(45 kg). Maximum total capacity of the pipe racks
and platform combined is as follows:
2033E3/2646E3 - 650 lb. (295 kg)
2046E3/2658E3 - 900 lb. (408 kg)
6. Maximum capacity of the manual platform extension
is 250 lb. (120 kg) - 1 person.
7. For Models 2033E3, 2046E3, 2646E3, and 2658E3
only, maximum capacity of the optional 4 ft. (1.2 m)
powered deck extension is 750 lb. (340 kg) - 2 per-
sons.
8. For Models 2033E3, 2046E3, 2646E3, and 2658E3
only, maximum capacity of the optional 6 ft. (1.8 m)
powered deck extension is 250 lb. (120 kg) - 1 per-
son.
NOTE: It is important to remember that the load should be
evenly distributed on the platform. The load should
be placed near the center of the platform when pos-
sible.