JLG 2658E3 ANSI Service Manual - Manual (Page 9)

SECTION 1 - SPECIFICATIONS
3120762 – JLG Lift – 1-3
Machine Height (Platform Fully Elevated)
1532E3 - 15 ft (4.6 m)
1932E3 - 19 ft (5.8 m)
2033E3/2046E3 - 20 ft (6.1 m)
2646E3/2658E3 - 26 ft (7.9 m)
Machine Height (Platform Lowered)
1532E3 - 75.75 in. (1.9 m).
1932E3 - 79.75 in. (2.0 m).
2033E3/2046E3 - 79.0 in. (2.0 m).
2646E3/2658E3 - 88.0 in. (2.2 m).
Platform Railing Height
Standard Handrails
1532E3/1932E3/2033E3/2046E3 - 39.5 in (1.0 m)
2646E3/2658E3 - (Fold down rails standard) - 43.5 in (1.1
m)
Fold-Down Handrails
All Models - 43.5 in (1.1 m)
Machine Height (Platform Lowered - Fold
Downs Folded)
1532E3 - 72 in (1.8 m)
1932E3 - 76 in (1.9 m)
2033E3/2046E3 - 65.5 in (1.7 m)
2646E3/2658E3 - 74.5 in (1.9 m)
Machine Length
1532E3/1932E3 - 71.25 in (1.8 m)
2033E3/2046E3/2646E3/2658E3 - 100 in (2.5 m)
Machine Width
1532E3/1932E3 w/standard tires - 32.5 in (0.8 m)
2033E3 w/standard tires - 33.0 in (0.8 m)
2046E3/2646E3 w/standard tires - 46.0 in (1.2 m)
2658E3 w/standard tires - 58.0 in (1.5 m)
2046E3/2646E3/2658E3 w/optional flotation tires - 60.0 in
(1.5 m)
Ground Clearance
With Platform Lowered.
1532E3/1932E3/2033E3 - 3.00 in (7.6 cm)
2046E3/2646E3/2658E3 - 3.50 in (8.9 cm)
With Platform Elevated - (Pothole Protection System
Lowered)
All Models - 0.75 in (1.9 cm)
Maximum Tire Load
1532E3 - 1,060 lb (481 kg)
1932E3 - 1,100 lb (499 kg)
2033E3 - 1,410 lb (640 kg)
2046E3 - 1,710 lb (776 kg)
2646E3 - 1,750 lb (794 kg)
2658E3 - 1,950 lb (885 kg)
Maximum Bearing Pressure
1523E3 - 92 psi (6.5 kg/cm
2
)
1932E3 - 94 psi (6.6 kg/cm 2 )
2033E3 - 102 psi (7.2 kg/cm 2 )
2046E3 - 117 psi (8.2 kg/cm
2
)
2646E3 - 119 psi (8.4 kg/cm
2
)
2658E3 - 130 psi (9.1 kg/cm
2
)
1.4 TORQUE REQUIREMENTS
* Torque nut to 125-150 ft lbs (dry), then add extra torque
to line up the slot with the hole in the shaft to install the
cotter pin.
NOTE: When maintenance becomes necessary or a fas-
tener has loosened, refer to the Torque Chart to
determine proper torque value.
Table 1-3. Torque Requirements
DESCRIPTION
TORQUE VALUE
(DRY)
INTERVAL HOURS
Wheel Lugs 105-120 ft lb
(147-168 Nm)
500
Wheel Hub to Drive
Motor
125-150 ft lb*
(169-203 Nm)
600
Motor Controller
Battery Terminal
Nuts
60 in lb
(7Nm)
At Controller
Replacement Only