Echo CH9540H Owners Manual v.3 - Manual (Page 4)

PTO CHIPPERS iv
TabLE oF CoNTENTS
SaFETY ......................................................................... 1
1.1 SAFeTY AleRT SYMBOl ........................................ 1
1.2 eMISSION INFORMATION ....................................... 1
1.3 BeFORe OPeRATING .............................................. 1
1.4 OPeRATION SAFeTY .............................................. 2
1.5 Feed ROlleR SAFeTY .......................................... 2
1.6 MAINTeNANce/STORAGe SAFeTY ....................... 3
1.7 TOWING SAFeTY ..................................................... 3
1.8 PTO SAFeTY ............................................................ 3
1.9 SAFeTY decAl lOcATIONS ................................. 4
1.10 SAFeTY decAlS ................................................... 5
aSSEmbLY .................................................................... 6
2.1 ATTAch chuTe SuPPORT (hYdRAulIc Feed
MOdelS ONlY) ........................................................ 6
2.2 ATTAch chIPPeR chuTe ...................................... 6
2.3 ATTAch exTeNSION TRAY ..................................... 7
2.4 cONNecTING POWeR FOR .................................. 7
2.5 SAFeTY BAR ............................................................. 7
2.6 ATTAch dISchARGe TuBe .................................... 7
2.7 ATTAch dISchARGe TuBe .................................... 8
2.8 cONNecT PTO ShAFT............................................ 8
FEaTuRES & CoNTRoLS ............................................ 9
opERaTIoN ................................................................ 10
4.1 STARTING The chIPPeR ...................................... 10
4.2 STOPPING The chIPPeR ...................................... 10
4.3 OPeRATING The chIPPeR .................................. 10
4.4 Feed ROlleR cONTROl BAR .............................11
4.5 Feed ROlleR cONTROl SPeed .........................11
4.6 lOck exTeNSION TRAY INTO TRAVel POSITION
(euRO MOdelS ONlY) ...........................................11
SERvICE & maINTENaNCE ....................................... 12
5.1 INSTAllING The dISk lOck ............................... 13
5.2 chIPPeR BlAde MAINTeNANce ........................ 13
5.3 ReMOVING The BlAdeS ..................................... 13
5.4 ShARPeNING The BlAdeS ................................. 14
5.5 AdjuSTING The chIPPeR ANVIl ........................ 14
5.6 luBRIcATION ........................................................ 15
5.7 PTO dRIVelINe luBRIcATION ............................ 16
5.8 cleARING PluGGed ROTOR .............................. 16
5.9 AdjuSTING/RePlAcING dRIVe BelT .................. 17
5.10 RePlAcING BeARINGS ...................................... 17
5.11 chANGING hYdRAulIc OIl FIlTeR .................. 18
5.12 FIllING hYdRAulIc FluId................................ 18
TRoubLESHooTING ................................................. 19
SpECIFICaTIoNS ........................................................ 20
7.1 chIPPeR SPecIFIcATIONS ................................... 20
7.2 BOlT TORQue ........................................................ 21
7.3 FlASh cOdeS FOR The cONTROl lIGhT ......... 22