Echo CH9540H Owners Manual v.3 - Manual (Page 9)

PTO CHIPPERS 5
ENGLISH
SAFETY
check BlAde BOlTS
FOR PROPeR TORQue
AFTeR eVeRY 8 hOuRS
OF OPeRATION. check
BlAdeS ANd ROTATe OR
ReShARPeN dAIlY OR
AS ReQuIRed TO keeP
BlAdeS ShARP. ReFeR TO OWNeRS MANuAl FOR
INSTRucTIONS. FAIluRe TO dO SO MAY cAuSe POOR
PeRFORMANce, dAMAGe OR PeRSONAl INjuRY ANd
WIll VOId The MAchINe WARRANTY.
keeP hANdS ANd FeeT OuT
OF INleT ANd dISchARGe
OPeNINGS WhIle MAchINe
IS OPeRATING TO AVOId
SeRIOuS PeRSONAl
INjuRY. STOP ANd AllOW
MAchINe TO cOMe TO A
cOMPleTe STOP BeFORe cleARING OBSTRucTIONS.
dO NOT OPeRATe ThIS
eQuIPMeNT IN The VIcINITY
OF BYSTANdeRS. dO
NOT AllOW chIldReN TO
OPeRATe ThIS eQuIPMeNT.
AlWAYS STANd cleAR OF
dISchARGe AReA WheN
OPeRATING ThIS MAchINe. keeP FAce ANd BOdY AWAY
FROM dISchARGe AReAS.
pN 12169
3 pN 12172
4
pN 12173
5
pN 12174
6
pN 12175
7
pN 12168
2
pN 14942-00
1
pN 12250
8
1.10 SaFETY dECaLS
9 pN 18983-00
(modELS CH9540H aNd
CHF9540H oNLY)
See Section 1.9 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine
and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety
instructions and decals. Make certain that all safety and operational decals on this machine are kept clean and in good
condition. decals that need replacement must be applied to their original locations.
cONTAcT WITh ROTATING
dRIVelINe cAN cAuSe
deATh. dO NOT OPeRATe
WIThOuT All dRIVelINe,
TRAcTOR ANd eQuIPMeNT
ShIeldS IN PlAce. eNSuRe The dRIVelINe IS SecuRelY
ATTAched AT BOTh eNdS ANd dRIVelINe ShIeldS ThAT
TuRN FReelY ON The dRIVelINe ARe IN PlAce.
keeP hANdS ANd FeeT OuT OF
INleT ANd dISchARGe OPeNINGS
WhIle MAchINe IS OPeRATING TO
AVOId SeRIOuS PeRSONAl INjuRY.
STOP ANd AllOW MAchINe TO cOMe
TO A cOMPleTe STOP BeFORe
cleARING OBSTRucTIONS.
ReAd ANd uNdeRSTANd ThIS
OWNeR/OPeRATORS MANuAl.
Be cOMPleTelY FAMIlIAR
WITh The cONTROlS ANd
The PROPeR uSe OF ThIS
eQuIPMeNT
OBTAIN ANd WeAR SAFeTY
GlASSeS ANd uSe heARING
PROTecTION AT All TIMeS
WheN OPeRATING ThIS
MAchINe.
BeFORe INSPecTING OR
SeRVIcING ANY PART OF ThIS
MAchINe, ShuT OFF POWeR
SOuRce, ReMOVe The keY,
dIScONNecT SPARk PluG WIRe
FROM SPARk PluG ANd MAke
SuRe All MOVING PARTS hAVe
cOMe TO A cOMPleTe STOP.
dO NOT OPeRATe MAchINe
WIThOuT ShIeldS IN PlAce.
FAIluRe TO dO SO MAY cAuSe
SeRIOuS INjuRY OR deATh.
Feed ROlleR SuPPORT
MuST Be SecuRed IN The
uP POSITION PRIOR TO
SeRVIcING chIPPeR Feed
AReA. The Feed ROlleR
cAN FAll ANd cAuSe
SeVeRe BOdIlY hARM. cONSulT OWNeRS MANuAl FOR
PROPeR MeThOd OF SecuRING Feed ROlleR SuPPORT.
lOWeR Feed ROlleR BeFORe OPeRATING chIPPeR.