Battery Tender High Frequency On Board Battery Charger 48V @ 10A (PN 022-0170-1) Installation User Manual

Caution, Warning, Suggested permanent mounting locations

Advertising
background image

DELTRAN CORPORATION

801 International Speedway Blvd.

DeLand, Florida 32724

Phone 386-736-7900 FAX 386-736-0379

www.batterytender.com

2

1

3

6

5

4

1

2

4

3

Suggested Permanent Mounting Locations.

CAUTION

Charger must be mounted in a location
that has at least four inches of clearance
between the heat sink fins and golf cart,
and is not in direct contact with rain or
splashing water.

Mounted underneath
rear seat (if equipped)

Mounted on 90 degree bracket
next to batteries.

Mounted on tub above
rear axle.

Supplied AC Cord

Supplied DC
Output Leads
or 12AWG Wire

24 or 48 volt

36 or 48 volt

48 volt

WARNING

Verify that the voltage of the charger matches
the voltage of the battery pack that the
charger is being connected to. Using the
improper charger may result in damaged to
charger and/or batteries.

Wiring Instructions for SMT Golf Car Charger:

1. Verify that the battery pack voltage matches the chargers voltage, if uncertain check battery pack with a volt meter.
2. Mount the charger in a location that is not in direct contact with rain or splashing water, and has at least 4 inches
of clearance for the cooling fins to function properly.
3. Connect the DC output leads small ring terminals to the charger, red wire to positive, and black wire to negative.
4. Connect the DC output cables large ring terminals to the battery pack, red wire to
the positive wire of the battery pack, and black wire to the negative.
5. Install (optional) Battery Capacity Gauge according to instructions
supplied with the optional products.
6. Connect AC cord to charger. Plug into grounded wall
outlet when batteries need charging.

P

A

R

T

N

O

.

0

2

2

-0

1

6

9

-1

IN

P

U

T

:

1

0

0

-1

2

0

V

~

,

11

A

,

5

0

/6

0

H

z

O

U

T

P

U

T

:

3

6

V

,

1

5

A

M

a

d

e

i

n

C

h

in

a

2

1

3

4

5

6

Front

Golf Cart

3

4

6

5

2

7

1

8

Black

Red

Battery Capacity
Gauge
(Optional
Equipment)

Refer to Battery Capacity
Gauge instruction manual
for installation of gauge.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

:

This manual contains important

safety and operating instructions for the Battery Tender Battery Chargerâ

High Frequency SMT Golf Car Chargers.

CAREFULLY READ THESE

INSTRUCTIONS BEFORE USING THE BATTERY CHARGER.

WARNING AND CAUTION LABEL DEFINITIONS:

WARNING

WARNING indicates a potentially hazardous situation, which, if

not avoided, could result in serious injury or death.

CAUTION

CAUTION indicates a potentially hazardous situation, which, if

not avoided, may result in minor or moderate injury.

CAUTION

CAUTION used without the safety alert symbol indicates a

potentially hazardous situation that if not avoided, may result in

property damage.

GENERAL PRECAUTIONS

WARNING

Battery posts, terminals and related accessories contain lead

and lead components, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Always wash your hands after handling

these devices.

High Frequency SMT Golf Car Charger

Battery Tender Battery Chargerâ Models:

12 Volt 20 Amp, 24 Volt 20 Amp, 36 Volt 15 Amp, 48 Volt 10 Amp

WARNING

– RISK OF EXPLOSIVE GASES

WORKING WITH LEAD ACID BATTERIES AND BATTERY CHARGERS:

All lead acid batteries have the potential to emit gasses that may combine into a

combustible or explosive mixture. In many cases, it is possible that lead acid

batteries will emit these gasses during normal discharge and charging operations.

Because of this potential danger, it is important that you follow the precautions

recommended by both the battery and battery charger manufacturers before using

either one.

USING MANUALS:

Study all of the battery manufacturer's precautions and

specific recommendations for safe operation such as not removing cell caps while

charging and the recommended rates of charge (charger output current

).

Installation Instructions for Permanent

Vehicle Mounting

1

2

12 volt

Mounting holes diameter
3/16" use #10 hardware.

Mounting hole
diameter 11/64"
use #8 hardware

7.75"

13"

1.5"

6.5"

11.5"

3.5"

25A Fuse

Advertising
This manual is related to the following products: