Comelit MT 3451 FR - Manual (Page 24)

24
CALL USER
_ _ _ 100
CALL CANC
CALL MANAGEMENT
*SIMPLEBUS
SIMPLEBUS TOP
OK OK
SCROLL ESC
CALL MANAGEMENT
*STANDARD
INDIRECT CODE
IMMOTEC STAND.
OK OK
SCROLL ESC
SYSTEM PARAMETERS
SELECT LANGUAGE
SECOND LANGUAGE
CALL MANAGEMENT
OK OK
SCROLL ESC
SELECT LANGUAGE
SECOND LANGUAGE
CALL MANAGEMENT
ACCESS CONTROL
OK OK
SCROLL ESC
EN
Art. 3451/FR can be used in conjunction with the Simplekey module
Art. SK9020 by connecting the two products via RS485 (see
diagram on page 80).
In this confi guration, the use of Simplekey access keys (badges)
automatically allows entry of the corresponding code/name (new
key) or updating of the name only (if the code already exists) in the
directory of Art. 3451/FR. Since a single user code (apartment) can
have up to 2 access keys associated with it under different names,
during a numeric code call from the digital module the fi rst name of
the 2 in alphabetical order will be displayed.
N.B.: names cannot be entered and changed manually.
Badge acquisition only takes place when digital mode is in
standby
This call mode is only available when "access control" is
disabled
This call mode is only available when "access control" is
disabled
Art. 3451/FR can be used in conjunction with the Simplekey module
Art. SK9020 by connecting the two products via RS485 (see
diagram on page 80).
In this confi guration the use of access keys allows automatic
updating of the Simplekey access key (badge) name only, as
it appears in the directory of Art. 3451/FR. The Immotec indirect
codes and corresponding names can only be entered from a PC
using software Art. 1249B (R.I. 003 - SW rev. 2.3 or higher). Since
a single user code (apartment) can have up to 2 access keys
associated with it under different names, during a numeric code call
from the digital module the fi rst name of the 2 in alphabetical order
will be displayed.
N.B.: names cannot be entered and modifi ed manually.
Badge acquisition only takes place when digital mode is
in standby
The call can be made in the following ways:
√ During normal operation
1. Enter the indirect code (e.g. 100).
2. Press
to make the call or to cancel and exit.
IMMOTEC STANDARD
IMMOTEC INDIRECT
or:
1. Scroll through the directory using .
2. Press to make the call or to exit.
6. Select the call mode and confi rm.
7. Set the speaker module selector to OFF.
2.6. Access control
1. Access programming mode, see page 17.
2. Select settings/access control.
Art. 3451/FR can operate in two modes:
• "access
control" disabled: in this mode, every name can be
assigned a call code, which is saved in the directory. The entry
passwords must be entered separately and are not assigned to
any name.
• "access control" enabled: in this mode, a call code, an indirect
code (only in case of indirect call), a password and an RFID key
can be saved for every name listed in the directory. The option of
assigning a password or key to a name allows access identifi cation.
When access control is enabled, the following cannot be used:
• Immotec call mode
• data loading from 1249B (R.I. 003 - SW rev. 2.3 or higher)
To switch from "access control" disabled to "access control"
enabled, all saved passwords must be deleted
To switch from "access control" enabled to "access control"
disabled, all saved passwords and keys must be deleted
3. Access programming mode, see page 17.
4. Select settings/call management
.
1. Set the speaker unit selector to ON, see Fig.
2. Connect the terminal block.
5. Select the system type and confi rm.