Document Outline

• AS-i Safety Monitor for 2 AS-i circuits
  • Declaration of Conformity
  • 1. Symbol catalog
    • 1.1 Abbreviations
  • 2. General
    • 2.1 Product information
    • 2.2 Brief description
    • 2.3 Conformity statement
    • 2.4 Certification according to DIN EN ISO 9001 : 2000
  • 3. Safety
    • 3.1 Safety standard
    • 3.2 Intended use
      • 3.2.1 Conditions of use
      • 3.2.2 Residual risks (EN 292-1)
      • 3.2.3 Areas of application
    • 3.3 Organizational requirements
      • 3.3.1 Documentation
      • 3.3.2 Traceability of the devices
      • 3.3.3 Safety regulations
      • 3.3.4 Qualified personnel
      • 3.3.5 Repair
    • 3.4 Disposal
  • 4. Spezifications
    • 4.1 Technical data
      • 4.1.1 Data sheet 103303
    • 4.2 Consideration of failure probability according to IEC 61 508
    • 4.3 Scope of delivery
  • 5. Installation
    • 5.1 Dimensions
    • 5.2 Connections
    • 5.3 Installing in the control cabinet
    • 5.4 Removing
    • 5.5 Electrical Connection
    • 5.6 Commissioning
      • 5.6.1 Supply voltage for AS-I Safety Monitor
      • 5.6.2 Duplicate address recognition
      • 5.6.3 Replacing the chip card
      • 5.6.4 Local parameter setting of safe AS-i/Gateways and Monitors
      • 5.6.5 Replacing a defective safety-configured AS-i slave
    • 5.7 Safe configuration using ASIMON 3 G2
  • 6. Maintenance
    • 6.1 Checking for safe turn-off
  • 7. Electrical connection
    • 7.1 Overview of terminals, indicators and operating elements
      • 7.1.1 103303
    • 7.2 AS-i bus connection
    • 7.3 Information about the device types
    • 7.4 AS-i and power supply terminal assignments
      • 7.4.1 Electrical connection 103303
    • 7.5 Diagnostics interface
      • 7.5.1 103303
    • 7.6 Chip card
    • 7.7 Release circuits
      • 7.7.1 Wiring overview of Safety Monitor 103303
    • 7.8 Indicators and operating elements
      • 7.8.1 LED indicators - Monitor 103303
      • 7.8.2 LED indicators safety unit in 103303
      • 7.8.3 Buttons
  • 8. Function and startup of the Safety Monitor
    • 8.1 Powering up the device
    • 8.2 Configuration of the safety functions
      • 8.2.1 Description of configuration using ASIMON 3 G2 software
      • 8.2.2 Description of configuration using chip card with master configuration
      • 8.2.3 Configuration using a chip card with complete configuration
    • 8.3 Safety-relevant documentation of the application
    • 8.4 Diagnostic data
      • 8.4.1 Switch-off history
      • 8.4.2 Profile and diagnostics using AS-i
    • 8.5 Password protection
      • 8.5.1 Procedure for configuring and teaching code sequences
      • 8.5.2 Function of the ESC/Service key
    • 8.6 Safe coupling slaves on the AS-i circuits
    • 8.7 Chip card
      • 8.7.1 Unsafe data
      • 8.7.2 Working with multiple memory banks
  • 9. Operation in advanced display mode
    • 9.1 Overview
    • 9.2 Navigation in advanced mode
    • 9.3 AS-I SAFETY
      • 9.3.1 TEACH CODES
      • 9.3.2 SAFE OUTPUT CH (channels for the release circuits)
      • 9.3.3 SAFE COUPLING (optional menu)
      • 9.3.4 START/STOP (changing the Monitor mode)
      • 9.3.5 CLEAR SAFE CFG (delete safe configuration)
      • 9.3.6 PIN (changing the PIN)
      • 9.3.7 SAFE CHIPCARD
      • 9.3.8 PROTECT (protect safe configuration)
    • 9.4 DIAGNOSTICS
      • 9.4.1 AS-I CIRCUIT (Selecting the AS-i circuit)
      • 9.4.2 SAFETY SLAVES (safety oriented slaves)
      • 9.4.3 MONITOR
      • 9.4.4 FAULT DETECTOR
      • 9.4.5 ERROR COUNTERS
      • 9.4.6 LPF (List of Peripheral Faults)
      • 9.4.7 AS-I MONITOR (Info)
    • 9.5 SETUP
      • 9.5.1 CHIPCARD
      • 9.5.2 Language (menu language)
      • 9.5.3 FACTORY RESET (factory default settings)
    • 9.6 DISPLAY CONTRAST (set display contrast)
  • 10. Configuration mit Windows Software ASIMON 3 G2
  • 11. Diagnostics for AS-i Monitor and networking using AS-i Master
    • 11.1 Introduction
    • 11.2 On-location operation
    • 11.3 Spontaneous messages
    • 11.4 Diagnostics using Profile S-7.5.5
      • 11.4.1 Binary data
      • 11.4.2 Transparent input data
      • 11.4.3 Acyclical data
  • 12. Status indication, faults and fault elimination
    • 12.1 Spontaneous display of faults from the safety unit
    • 12.2 Replacing a defective safety-configured AS-i slave
    • 12.3 Replacing a defective AS-i Safety Monitor
    • 12.4 Forget the password? What do I do now?
  • 13. Glossary: As-i terms
  • 14. Accessories
    • 14.1 AS-i Safety at Work
      • 14.1.1 AS-i 3.0 PROFIBUS-Gateway with integrated Safety Monitor Features:
  • 15. Reference List
    • 15.1 Manual: “ASIMON 3 G2 Configuration Software“
    • 15.2 Sources
  • 16. Your opinion is important to us!