Document Outline

• Trademarks
• Copyright © 2009 byHYDAC Filtertechnik GmbHall rights reserved
• Exclusion of liability
• Content
• Preface
  • Technical Support
  • Product modification
  • Warranty
  • Using the documentation
• General safety guidelines
  • Obligations and liability
  • Explanation of symbols and warnings
    • Basic symbols
  • Intended use
  • Improper use
  • Informal safety precautions
  • Training and instruction of personnel
• New features — instruction modifications
• Storing ContaminationSensor
  • Storage conditions
• Interpreting the type label
• Checking the scope of delivery
• CS1000 Features
  • CS1000 Restrictions on use
  • CS1x1x dimensions (without display)
  • CS1x2x dimensions (with display)
  • Hydraulic connection types
    • Pipe or hose connection (Type CS1xxx-x-x-x-x-0/-xxx)
    • Flange connection type (Type CS1xxx-x-x-x-x-1/-xxx)
  • Fastening / mounting the CS1000
  • Display rotatable/Adjustable As Needed
  • CS1000 hydraulic installation
    • Selecting the measurement point
    • Flow rate, differential pressure and viscosity characteristics
    • Hydraulic connection of the CS1000
  • Electrical connection of the CS1000
    • Pin assignment
    • Connection cable - Assignment / Color coding
    • Connecting cable ends - Examples
• CS measurement modes
  • Mode M1: Continuous measurement
  • Mode M2: Continuous measurement and switching
  • Mode M3: Filter to cleanliness class and stop
  • Mode M4: Filter to continuously monitor cleanliness class
  • Mode "SINGLE" individual measurement
• Operating the CS1000 per keyboard (Only CS1x2x)
  • Measurement categories
    • ISO (Cleanliness class)
    • SAE (Cleanliness class)
    • NAS (Cleanliness Class - only CS 13xx)
  • Service categories
    • Flow (flow rate)
    • Out (Analog output)
    • Drive (performance of the LED)
    • Temp (Temperature)
  • Activating/deactivating key lock
  • Modes and menus
    • Power Up menu
    • Measuring Menu
• Display — Select display after switching on the sensor
• ANA.OUT
  • Measuring menu (CS13xx)
• Display — Select displayed measurement category after switching on the sensor
• MODE – Configure measuring mode
• ANA.OUT
• Overview of menu structure
  • Menu CS 12xx (ISO 4406:1999 and SAE)
  • Menu CS 13xx (ISO 4406:1987 and NAS)
• Using switching output
  • Mode M1: Continuous measurement
  • Mode M2: Continuous measurement and switching
  • Mode M3: Filter to cleanliness class and stop
  • Mode M4: Filter to continuously monitor cleanliness class
  • "SINGLE" measurement mode
  • Setting limit values
• Analog Output (ANAOUT)
  • SAE classes acc. to AS 4059
    • SAE A-D (SAeMAX)
    • SAE Klassen A / B / C / D (SAE)
    • SAE A / SAE B / SAE C / SAE D (SAE A/SAE B/SAE C/SAE D)
    • SAE + T (SAE+T)
    • HDA.SAE – Analog signal SAE to the HDA 5500
• HDA.SAE Signal 1/2/3/4
• HDA Status Signal 5
  • ISO Code acc. to 4406:1999
    • ISO 4 / ISO 6 / ISO 14 (ISO 4 / ISO 6 / ISO 14)
    • ISO code (ISO), 3-digit
    • ISO + T (ISO+T)
    • HDA.SAE – Analog signal ISO to HDA 5500
• HDA.ISO Signal 1/2/3/4
• HDA Status Signal 5
  • ISO code signal acc. to 4406:1987 (CS 13xx only)
    • ISO 2 / ISO 5 / ISO 15 (ISO 2 / ISO 5 / ISO 15)
    • ISO code (ISO), 3-digit
    • ISO + T (ISO+T)
    • HDA.ISO – Analog signal ISO to HDA 5500
• HDA.ISO Signal 1/2/3/4
• HDA Status Signal 5
  • NAS 1638 - National Aerospace Standard (Only CS 13xx)
    • NAS Maximum (NAsMAX)
    • NAS classes (2 / 5 / 15 / 25) (NAS)
    • NAS 2 / NAS 5 / NAS 15 / NAS 25 (NAS 2/NAS 5/NAS 15/NAS 25)
    • NAS + T (NAS+T)
    • HDA.NAS – Analog Signal NAS to HDA 5500
• HDA Signal 1/2/3/4
• HDA Status Signal 5
  • Fluid temperature (TEMP)
• Status messages
  • Status LED / display
  • Error
  • Exception errors
  • Analog output error signals
    • Analog signal for HDA 5500
• HDA status signal 5 table
• Connecting CSI-D-5 (Condition Sensor Interface)
  • CSI-D-5 Connection overview
• CS1000 in RS-485 bus
• Taking the CS1000 out of operation
  • Disposing of CS1000
• Spare parts and accessories
• Cleanliness classes - brief overview
  • Cleanliness class - ISO 4406:1999
    • Table - ISO 4406
    • Overview of modifications - ISO4406:1987 vs. ISO4406:1999
  • Cleanliness class - SAE AS 4059
    • Table - SAE AS 4059
    • Definition acc. to SAE
• Particle count (absolute) larger than a defined particle size
• Specifying a cleanliness class for each particle size
• Specify highest measured cleanliness class
  • Cleanliness Class - NAS 1638
• Checking/resetting factory default settings
  • Power Up menu
  • Measuring menu
• Technical data
• Recalibration
• Customer service
• Model code