I.R.I.S. 595 - Manual (Page 2)

1.01 Conventions:
At various points within this guide, the following icons will be
used to illustrate important or potentially dangerous information:
! ! WARNING
! ! This symbol indicates a risk of damaging the
! ! camera or other items or an important issue that
! ! may effect the operation of the camera.
! ! INFORMATION
! ! This symbol points out important information
! ! pertaining to the installation, operation and
! ! maintenance of the camera.
! ! DANGER
! ! This symbols alerts the user of a serious risk of
! ! damage or personal injury or death.
1.02 Limited Warranty:
This product is warranted to be free from defects in materials or
workmanship for one year from the date of purchase. Upon
registration of the product an additional 12 months warranty will
be awarded FOC. Within this period, Iris Innovations will, at its
sole option, repair or replace any components that fail in normal
use. Such repairs or replacement will be made at no charge to
the customer for parts or labour, provided that the customer
shall be responsible for any transportation cost. This warranty
does not apply to: (i) cosmetic damage, such as scratches, nicks
and dents; (ii) consumable parts, such as batteries, unless
product damage has occurred due to a defect in materials or
workmanship; (iii) damage caused by accident, abuse, misuse,
water, flood, fire, or other acts of nature or external causes; (iv)
damage caused by service performed by anyone who is not an
authorized service provider of Iris Innovations Limited or Iris
Innovations USA Corporation; or (v) damage to a product that
has been modified or altered without the written permission of
Iris Innovations. In addition, Iris reserves the right to refuse
warranty claims against products or services that are obtained
and/or used in contravention of the laws of any country. This
product is intended to be used only as a travel aid and must not
be used for any purpose requiring precise measurement of
direction, distance, location or topograph
y.
2.01 Warnings & Important Product Information
WARNING: Installation and Operation
This product must be installed and operated in accordance with
these instructions. Failure to do so may result in poor product
performance, damage to the product or vessel and or personal
injury. Installation should only be carried out be qualified
personnel or by persons competent in electrical systems.
WARNING: Power Supply and Grounding
Ensure the boats power supply is switched off during
installation. Ensure suitably rated circuit breakers / fuses are
used in the installation of the product in accordance with the
electrical values shown in the technical specifications of the
product. Never switch on power until the power connections are
correctly terminated in accordance with the information provided
in this document. Do not connect or disconnect the product with
the power supply switched on. Never disconnect the DC ground
with the power supply on.
WARNING: Wiring terminations
Where the products, power and data terminations are extended,
ensure that suitable connectors are used and that the point of
termination for each cable is adequately protected against
moisture ingress. Ensure correct polarity is strictly observed. Do
not cut or remove cable connectors without prior permission
from Iris Innovations Limited.
WARNING: Do Not Open the Unit
There are no user serviceable parts within the product so thereʼs
no need to open the device. The product has been certified to
IP66 standards, however, submersion or the product or
exposure to high pressure washing will invalidate the warranty.
WARNING: Disclaimer
This product is intended to be used only as an aid to navigation
and must never be used as an alternative to correct navigational
practices and judgements made on the basis of approved
navigation methods. It is the users responsibility to observe
correct and proper navigational skill when using this product.
Only officially approved charts and notices to mariners contain
the current information required for safe navigation.
Operating the device or viewing the video input whilst the vessel
is moving could cause a distraction and result in accidental
collision resulting in property damage, injury or death. Iris
Innovations cannot be held liable for any incidental, special,
indirect or consequential damages whether resulting from the
use, misuse or inability to use this product.
CAUTION: Switch Controller Off When Not in Use.
To prolong the operation life of the thermal cameraʼs micro-
bolometer sensor we strongly advise that power to the camera is
routed via a dedicated switch.
CAUTION: Service and Maintenance
This product contains no user serviceable parts. Please refer all
maintenance and repair issues to your authorized Iris
Innovations dealer. Any unauthorized work to the product may
affect the warranty.
CAUTION: Care and Cleaning
This product is a sensitive piece of electronic, imaging
equipment and must be handled and treated accordingly. Do not
drop or shake the unit during installation. Never manually alter
the pan or tilt position whilst the power to the unit is on as this
may permanently damage the motors. Avoid exposure of the
imager to direct sunlight where possible as this may degrade the
cameras performance over time.
When cleaning the device, ensure power is switched off to avoid
unintentional movement of the cameras motors. Clean the
camera housing with a soft cloth. Moisten the cloth and use a
mild detergent if required but take care not to get detergent on
the lens window. The lens window has a protective coating
which may suffer damage as a result of improper cleaning. To
clean the lens window use a soft cotton cloth. Moisten with clean
water if necessary. For further advise on cleaning the lens
window, contact Iris Innovations.