Opticon PHL 7100 Quick Guide - Manual (Page 2)

RESETTING DEVICE RESETTING DEVICE
SETTING DEVICE SETTING DEVICE
1. Initial Boot Up
The initial boot up screen will be displayed
when you install battery pack at the first
time. Do not remove Battery Pack when
system is at initial boot up.
2. Calibrating Touch Screen
This calibration is already done by manufacturer.
If you want to calibrate the touch screen again,
please tap “Start” --- “Settings” --- “Control Panel
” --- “Stylus” --- “Calibration" --- "Recalibrate”,
then hold the stylus and press on the center of
each target as it moves around the screen.
3. Setting Up Wireless LAN
1) Press “Start”---“Settings”---“Control Panel”--- “WLAN Manager”.
2) Launch the WLAN Manager to Enable WLAN device.
3) Into AP Browser tab, tap Scan button to renew the network.
4) Select a network, tap the Join button or double tap it for
more options.
5) Press OK to save all your WLAN settings.
6) Tap the “Exit” button to Disable WLAN device.
availability depends of PHL-7000 model. Note :
5. Brightness Setting
The device is equipped with backlight for both
sunlight-readable LCD display and keypad.
To adjust the LCD backlight brightness, press
the “Fn” key and then press navigation key
“>” or “<” to adjust display brightness.
Press “Start”---“Settings”---“Control Panel” ---
“Control Center” “Brightness”
both LCD
and Keypad brightness.
Or
to set
6. Volume Adjusting
1) Press “Start”---“Settings”---“Control Panel”
-- “Volume & Sounds”.
2) Adjust the volume bar to meet your demand.
To mute the sound, press the “Fn” key and then
press “ESC” key to turn off and on the sound.
Note:
USING THE APPLICATIONS
1. Execute an “Application”
Tap an application icon on the desktop, or tap
“Start”---“Programs”. Select one of the applications.
2. Close an “Application”
Tap the tab of “X” to close the application.
3. Using the Software Input Panel
1) Tap the “Stylus” icon on the “task bar”.
2) Tap the “Keyboard” icon.
3) When Software Input Panel appears, input
characters with the Stylus.
4. Task Switch
Win CE can execute multiple applications
at the same time.
1) Press “Task Switch” icon in the task bar.
2) Select the task(s) you want in the task menu.
During the execution of applications, when you select the menu
“Desktop”, brings the selected application to the foreground.
It does not close the other applications.
BAR CODE READING BAR CODE READING
Remove the protective film from the scan window before use.
1. Start your application
2. Aim the scan window at the bar code
3. Press one of the three bar code reader trigger
buttons
4. Aiming :
1D laser: aim the red laser beam on the center of the bar code
Bar codes can be read from 50 to 650 mm distance.
USING PERIPHERALS USING PERIPHERALS
1. Using CF Type Peripherals
2. Using SD / MMC Type Card
1) Remove the 4 screws from the End Cap with
a screw driver, Torx type and size 8 (T8).
2) Insert the CF memory cards into the
CF Support Guide. Insert a correctly
oriented CF card.
3) Using 4 ~ 4.5 kgf-cm torque to fix the screws for End Cap.
availablility depends of PHL-7000 model.
1)
2) Insert a correctly oriented SD/MMC card.
To remove SD/MMC card, press the card again and slot
will pop out card automatically.
3)
Remove the 4 screws from the End Cap with
a screw driver, Torx type and size 8 (T8).
Using 4 ~ 4.5 kgf-cm torque to fix the screws for End Cap.
Note:
Note:
The SD/MMC slot support memory card only. It does not support
SD I/O peripherals. The SD/MMC slot support memory card only. It does not support
SD I/O peripherals.
3. USB Connection
Connect the USB client cable to synchronize data with a computer.
Be sure the HRS mark on the connector of USB cable to be upward
when you insert cable to devices. To remove cable from device,
press both buttons on connector and then remove connector from
device.
Use Microsoft ActiveSync version 3.7 or above. Note:
1. Warm Reset
1) If an application hangs, initiate Warm Reset to terminate
the application.
2) Warm Reset will close all applications and clear the working
RAM, but all files will be preserved.
3) To perform Warm Reset, press “F1” and “F4” buttons
simultaneously.
CAUTION: !
A. Do not stare into the laser beam directly or shine it
into eyes.
B. Never use strong pressure onto the screen or subject
it to severe impact, as the LCD panel could become
cracked and possibly cause personal injury. If the
LCD panel is broken, never touch the liquid inside,
because the liquid irritates the skin.
C. Use only the original approved AC adapter with the
PHL-7000. Use of an unapproved AC Adapter could
result in electrical problems,or even cause a fire or
electrical shock to the user.
D. Do not disassemble the PHL-7000. Servicing should
be done by Opticon only. If the PHL-7000 or
accessories gets damaged due to wrong handling
or unauthorized repair, warranty is void.In case the
warranty seals are broken, warranty is void too.
E. Make regularly back-ups of all important data.
F. Under no circumstance will Opticon be liable for any
direct, indirect,consequential or incidental damages
arising out of use or inability to use both the hardware
and software and/or any data loss, even if Opticon
has been informed about the possibility of such
damages.
Do not throw this product in the home waste bin.
For proper end-of-life treatment consult the
Environmental care section of www.opticon.com
For CE, FCC and other DoC's, consult the
Regulatory section of www.opticon.com
communication
PHL-7100
Quick Guide
huma
nizat
ion
managemen
t
User and Product Safety
CAUTION: !
CAUTION: !
Start Button Close Button
Keyboard input panel.
Task Switch
CAUTION:
Be sure to use the supplied stylus or plastic-
tipped pens for touch screen display. Don't
use pencil, pen or any sharp object on touch
screen display.
4. Bluetooth Device Properties
Bluetooth Device Properties to enable
Bluetooth device.
2) Wait for 20 seconds in order to initialize the
Bluetooth hardware correctly.
) Press Scan device button to search for
Bluetooth devices.
availability depends of PHL-7000 model.
1) Press “Start”---“Settings”---“Control Panel”
-- “ ”
3
Note :
PHL-7100
2. Cold Reset
PHL-7100
Try before you initiate Cold Reset. All
applications will be closed, and working RAM as well as
all files will be cleared if you initiate the Cold Reset. It is
strongly recommended to back up your files to Flash ROM,
Flash Card or PC.
Warm Reset
Stylus/Keyboard icon
1) You can use Cold Reset to initialize the PHL-7000 if the
WinCE.NET OS locks up or in case a Warm Reset has no effect.
2) To perform Cold Reset, press “Power”, “F1” and “F4” buttons
simultaneously.
3) Device will boot up after Cold Reset.
5. Check the bar code reading result
You can verify the result of the bar code reading in your application,
by beep sound(s) or the LED indicator.
Sccltd Opticon
o p t i c o n
Opticon
o p t i c o n
Opticon
Good scanning positions
Bad scanning positions
o p t i c o n
Opticon
o p t i c o n
Opticon
o p t i c o n
Opticon
2D CMOS: 4 green aiming spots are visible. Position the bar code
between the 2 outer green light spots. Ideal reading
distance is where the 2 center green light spots joins.
The bar code is read in the red illumination area.
Bar codes can be read from 45 to 260 mm distance.
Good scanning positions
Bad scanning positions