Sportsliter Solutions Remote System - Manual (Page 8)

REMOTE SYSTEM
INSTALLATION
INSTRUCTIONS FOR CLAMP-ON COMPONENT MOUNTING TO CONCRETE POLES (FIG. 10)
FIELD SIDE
WIRING HARNESS
CONNECT TO PLUG IN REMOTE
BALLAST BOX AND JUNCTION
BOX AT TOP
SEAL ANY OPENINGS AROUND
BOTTOM ATTACHMENT POINT
WITH SILICONE SEALANT
SUPPLY WIRING
(BY OTHERS)
REMOTE BALLAST BOX
SECURE TO POLE WITH
¾” O BOLTS (2) AND
WASHERS SHIPPED WITH
BOX. (TIGHTEN TO 20 ft/lbs.
MAX)
JUNCTION BOX
CONCRETE POLE
BIRD GUARD/STRAIN RELIEF PLATE
(ADJUSTMENTS MAY BE REQ’D. FOR HOLE COVERAGE
AND ALIGNMENT OF WIREWAY OPENINGS)
TOP VIEW OF JUNCTION BOX
ATTACH WIRING HARNESS
STRAIN RELIEF HERE
SECURE JUNCTION BOX TO
CROSSARM ASSY. WITH ¼” O
BOLTS (2), WASHERS & NUTS
SHIPPED WITH JUNCTION BOX
GASKET BETWEEN POLE & REMOTE
BALLAST BOX FOR WATERTHGHT SEAL
THESE BOLTS SHIPPED WITH POLE
(TIGHTEN TO 20 ft/lbs MAX)
BOLT (2)
AND WASHERS
LOCK WASHER
NUT
FLAT WASHER
KEEP DISTANCE
TO A MINIMUM
CROSSARM ASSEMBLY
SECURE GRD WITH GRD SCREW
INSIDE JUNCTION BOX
CROSSARM
ANGLE
¾” O THD
ROD (4)
CROSSARM MOUNTING HARDWARE SHIPPED
WITH CROSSARM ASSEMBLY
NOTE: TIGHTEN ALL NUTS ON THREADED RODS
SNUG THEN AN ADDITIONAL ONE QUARTER TURN. DO
NOT OVERTIGHTEN TO CAUSE BENDING OF CHANNEL
OR CROSSARM ANGLES.
FOR DETAILED INSTALLATION INSTRUCTIONS
FOR THE REMOTE BOX, SEE THE INSTRUCTION
SHEET INCLUDED WITH EACH.
INSTRUCTIONS FOR CLAMP-ON COMPONENT MOUNTING TO CONCRETE POLES (FIG. 10)
FIELD SIDE
WIRING HARNESS
CONNECT TO PLUG IN REMOTE
BALLAST BOX AND JUNCTION
BOX AT TOP
SEAL ANY OPENINGS AROUND
BOTTOM ATTACHMENT POINT
WITH SILICONE SEALANT
SUPPLY WIRING
(BY OTHERS)
REMOTE BALLAST BOX
SECURE TO POLE WITH
¾” O BOLTS (2) AND
WASHERS SHIPPED WITH
BOX. (TIGHTEN TO 20 ft/lbs.
MAX)
JUNCTION BOX
CONCRETE POLE
BIRD GUARD/STRAIN RELIEF PLATE
(ADJUSTMENTS MAY BE REQ’D. FOR HOLE COVERAGE
AND ALIGNMENT OF WIREWAY OPENINGS)
TOP VIEW OF JUNCTION BOX
ATTACH WIRING HARNESS
STRAIN RELIEF HERE
SECURE JUNCTION BOX TO
CROSSARM ASSY. WITH ¼” O
BOLTS (2), WASHERS & NUTS
SHIPPED WITH JUNCTION BOX
GASKET BETWEEN POLE & REMOTE
BALLAST BOX FOR WATERTHGHT SEAL
THESE BOLTS SHIPPED WITH POLE
(TIGHTEN TO 20 ft/lbs MAX)
BOLT (2)
AND WASHERS
LOCK WASHER
NUT
FLAT WASHER
KEEP DISTANCE
TO A MINIMUM
CROSSARM ASSEMBLY
SECURE GRD WITH GRD SCREW
INSIDE JUNCTION BOX
CROSSARM
ANGLE
¾” O THD
ROD (4)
CROSSARM MOUNTING HARDWARE SHIPPED
WITH CROSSARM ASSEMBLY
NOTE: TIGHTEN ALL NUTS ON THREADED RODS
SNUG THEN AN ADDITIONAL ONE QUARTER TURN. DO
NOT OVERTIGHTEN TO CAUSE BENDING OF CHANNEL
OR CROSSARM ANGLES.
FOR DETAILED INSTALLATION INSTRUCTIONS
FOR THE REMOTE BOX, SEE THE INSTRUCTION
SHEET INCLUDED WITH EACH.
7