Zero Gravity Kawasaki ZX10 (11-Present) Windscreen User Manual

Zero Gravity For motorcycles

Advertising
background image

WWW.ZEROGRAVITY-RACING.COM

23, 24, 25-263

install Rev A

nut threaded receptacle. (See image up above).

8. Add the last 2 corner fasteners, then tighten all 6 windscreen fas-

tener screws so that the windscreen is firmly in place.
DO NOT OVER-TIGHTEN!

Installation Instructions for 23, 24, 25 Series Windscreen 2011- Present Kawasaki ZX-10R

Thank you for purchasing one of Zero Gravity’s windscreens which has been designed and manufactured to give years of safe and fun rid-
ing. This instruction manual gives you an in-depth look at the

installation process. To receive further assistance or parts please e-mail

techinfo@zerogravity-racing.com.

1 Spacer installed

between wellnut

and screen.

Well Nut

Locations

ZG Fasteners

Factory Washers Reuse

ZG Spacers

Factory Wellnuts

Windscreen

1.

Remove the factory windscreen.

2.

Before installing your new Zero

Gravity screen, locate the 2 spacers and 6

fasteners provided with your windscreen.

3.

Remove the 6 factory washers and reuse them on ZG fasteners. Place

your Zero Gravity windscreen on the bike and align the windscreen
holes with the windscreen cowling holes.

4.

Insert 2 of the 6 supplied ZG windscreen fastener screws into the 2
bottom holes and screw them in a few turns into the wellnuts.

5.

Lift the rear edge of the screen so the screen tilts up slightly.

6.

Place the 2 spacers between the windscreen and the windscreen cowl-
ing so they align with the 2 upper holes of the windscreen and the
well nut receptacle holes of the cowling. (See Well Nut Locations).

7.

Insert the 2 fasteners and washers into the upper windscreen holes so
that they pass through the windscreen, spacers, and then into the well-

SPORTBIKE SADDLES & WINDSCREENS

Well Nut Locations

Spacer location

between

windscreen

and cowling

Factory Windscreen Cowling

1 Spacer installed

between wellnut

and screen.

WWW.ZEROGRAVITY-RACING.COM

23, 24, 25-263

install Rev A

nut threaded receptacle. (See image up above).

8. Add the last 2 corner fasteners, then tighten all 6 windscreen fas-

tener screws so that the windscreen is firmly in place.
DO NOT OVER-TIGHTEN!

Installation Instructions for 23, 24, 25 Series Windscreen 2011- Present Kawasaki ZX-10R

Thank you for purchasing one of Zero Gravity’s windscreens which has been designed and manufactured to give years of safe and fun rid-
ing. This instruction manual gives you an in-depth look at the

installation process. To receive further assistance or parts please e-mail

techinfo@zerogravity-racing.com.

1 Spacer installed

between wellnut

and screen.

Well Nut

Locations

ZG Fasteners

Factory Washers Reuse

ZG Spacers

Factory Wellnuts

Windscreen

1.

Remove the factory windscreen.

2.

Before installing your new Zero

Gravity screen, locate the 2 spacers and 6

fasteners provided with your windscreen.

3.

Remove the 6 factory washers and reuse them on ZG fasteners. Place

your Zero Gravity windscreen on the bike and align the windscreen
holes with the windscreen cowling holes.

4.

Insert 2 of the 6 supplied ZG windscreen fastener screws into the 2
bottom holes and screw them in a few turns into the wellnuts.

5.

Lift the rear edge of the screen so the screen tilts up slightly.

6.

Place the 2 spacers between the windscreen and the windscreen cowl-
ing so they align with the 2 upper holes of the windscreen and the
well nut receptacle holes of the cowling. (See Well Nut Locations).

7.

Insert the 2 fasteners and washers into the upper windscreen holes so
that they pass through the windscreen, spacers, and then into the well-

SPORTBIKE SADDLES & WINDSCREENS

Well Nut Locations

Spacer location

between

windscreen

and cowling

Factory Windscreen Cowling

1 Spacer installed

between wellnut

and screen.

Advertising