Warning, Troubleshooting, Maintenance – Garden Sun Heater HPS-C-PC Tabletop Heater User Manual
Page 9
Troubleshooting
If the problem is:
And this condition exists:
Then do this
Pilot won’t light
Cylinder valve is closed
Open valve
Blockage in orifice or pilot tube
Clean or replace orifice or pilot tube
Air in gas line
Open gas line and bleed it (pressing control
knob in) for not more than 1 - 2 minutes or
until
you smell gas
Low gas pressure with cylinder valve
fully open
Turn cylinder valve OFF and replace
cylinder
Note:
Heater
operates
at
reduced efficiency below 40ºF
(5ºC)
Igniter fails
Use match to light pilot; obtain new igniter
and
replace
Pilot won’t stay lit
Dirt built up around pilot
Clean dirt from around pilot
Connection between gas valve and
pilot assembly is loose
Tighten connection and perform leak check
Thermocouple is not operating
correctly
Replace thermocouple
Burner won’t light
r
e
d
n
il
y
c
e
c
a
l
p
e
r
d
n
a
F
F
O
e
v
l
a
v
r
e
d
n
il
y
c
n
r
u
T
w
o
l
s
i
e
r
u
s
s
e
r
p
s
a
G
e
g
a
k
c
o
l
b
r
a
e
l
C
e
c
i
f
i
r
o
n
i
e
g
a
k
c
o
l
B
Control knob is not in ON position
Turn control knob to ON
Burner flame is low
r
e
d
n
il
y
c
e
c
a
l
p
e
r
d
n
a
F
F
O
e
v
l
a
v
r
e
d
n
il
y
c
n
r
u
T
w
o
l
s
i
e
r
u
s
s
e
r
p
s
a
G
Outdoor temperature is less than
40ºF
and tank is less than 1/4 full
Use a full cylinder
e
g
a
k
c
o
l
b
r
o
f
s
e
c
i
f
i
r
o
d
n
a
r
e
n
r
u
b
k
c
e
h
C
N
O
y
ll
u
f
b
o
n
k
l
o
r
t
n
o
C
Carbon build-up
Dirt or film on reflector and burner screen
Clean reflector and burner screen
Thick black smoke
Blockage in burner
Remove blockage and clean burner inside and
outside
8
Maintenance
WARNING
FOR YOUR SAFETY:
• Do NOT touch or move heater for at least 45 minutes
after use.
• Reflector is hot to the touch.
• Allow reflector to cool before touching.
To enjoy years of outstanding performance from your
heater, make sure you perform the following maintenance
activities on a regular basis:
Air flow must be unobstructed. Keep controls, burner,
and circulating air passageways clean. Signs of possible
blockage include:
a. Keeping the appliance area clear and free from combustible
materials , gasoline and other flammable vapors and liquids.
b. Not obstructing the flow of combustion and ventilation air.
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use
flammable or corrosive cleaning agents.
While cleaning your unit, be sure to keep the area around the
burner and pilot assembly dry at all times. Do not submerge the
control valve assembly. If the gas control is submerged in water,
do NOT use it. It must be replaced.
c.Keeping the ventilation opening(s) of the cylinder enclosure
free and clear from debris.
Normal
Abnormal