Sound Devices 722 - Manual (Page 65)

722 User Guide and Technical Information
63
# Setup Name Setup Description Setup Options
29 Line Input 1,2: Gain Control When inputs 1 and 2 are in LINE input mode, selects
whether the gain setting is controlled by the front
panel knobs or by the menu sensitivity settings below.
• Use front panel knobs
• Use sensitivity settings
30
31
Line Input 1: Gain
Line Input 2: Gain
Adjusts the input sensitivity of line-level inputs when
set to Use Sensitivity Settings.
Adjustable from -6 dB to +18 dB in 0.1 dB steps.
32
33
Input 1: Delay
Input 2: Delay
Sets a digital delay for each input. Can be used to
compensate for delay in various digital wireless micro-
phone units or digital processors.
0 to 30 milliseconds, 0.1 mS increments
0 mS to 30,000 mS up to 48.048 kHz Fs
0 mS to 15,000 mS up to 96.096 kHz Fs
0 mS to 7,500 mS up to 192 kHz Fs
34 File: Marker Mode Enables the user to set cue points on the fly while
recording by pressing the record key.
• Markers disabled
No cue marks are set.
• New Cue
Cue markers will be set within one contiguous
file.
• New File
A new file is started with each press of the record
key, the take counter is increased by one.
35 File: Max Size Selects the file size where the 722 will close, then
start a new file. The 722 will not record a file larger
than the selected size.
The largest file permissible with the 722’s FAT32 file
system is 4 GB
• 4 GB CF (3.6 GB)
• 2 GB CF (1.8 GB)
• 1 GB CF (950 MB)
• 512MB CF (450 MB)
36 File: Folder Options Allows user to organize files in root and sub-folders. To
not use any folders select <None> on every level.
• TOP-LEVEL
• MID-LEVEL
• BOTTOM-LEVEL <None>, <Add new entry>
<None>,<Add new entry>, <Daily>
<None>, <Add new entry>, <Scene>
37 File: View Files Enters the file directory tree for the selected drive. Highlight media descriptor to navigate the menu
38 File: View Take List Allows user to view the last 200 takes. Takes can be
selected and converted to circle takes.
• Circle
39 File: Copy Files Allows the user to select a file or a range of files to
be copied from one storage media to another. Files
will only be copied from their current directory to a
directory of the same name on the other media. If a
file will not fit on the destination media, user is given
the option to skip that file and continue with the copy
or abort the copy all together. User is advised at the
end of the copy process how many files were copied
successfully.
• Copy all {drive}  {drive}
• Last 24 hr {drive}  {drive}
• Last 48 hr {drive}  {drive}
• Flagged {drive}  {drive}
All files, when recorded, automatically have their
flag bit set to “on”
40 File: Copy Flag Reset Selects whether the flag bit is cleared or not on files
copied from one media to another.
• Disabled
• Enabled
41 Time Counter: Display Sets the numbers of the large numerical display. • Big A-time
• Big 24 hour time
42 Time Counter: Mode When set to 24 hour, the time counter is displayed
on the main LCD display. The time counter value is
derived from the 722 time of date clock. Recorded files
are stamped in metadata according to that value.
• Off
• 24 hour
43
44
Output 1 Left: Source
Output 1 Right: Source
Selects the signal source for the Master Output Bus
(TA3 Outputs and Tape Outputs).
• Input 1
• Input 2
• Track A
• Track B
• Input 1+2
• Track A+B
45 Output 1 L,R: Attenuation Selects the attenuation level of signal sent to the
Master Output Bus.
Selectable from 0 to -40 dBFS