Tweco 175i Transtig User Manual

175i operating manual, Transmig, Multi process welding inverter

Advertising

Table of contents

Document Outline

0-5143-CCr
SECTION 1:ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 2:INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3:INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Transmig 175i Power Source Controls, Indicators and Features
- 3.07 Attaching the Tweco Professional Fusion Mig Torch (Euro)
- 3.08 Installing Minispool (100mm diameter)
- 3.09 Installing Handispool (200mm diameter)
- 3.10 Inserting Wire into the Wire Feed Mechanism
- 3.11 Feed Roller Pressure Adjustment
- 3.12 Changing the Feed Roll
- 3.13 Wire Reel Brake
- 3.14 Shielding Gas Regulator Operating Instructions
- 3.15 Setup for MIG (GMAW) Welding with Gas Shielded Mig Wire
- 3.16 Setup for MIG (GMAW) Welding with Gasless Mig Wire
- 3.17 Setup for TIG (GTAW) Welding
- 3.18 Setup for Manual Arc (MMAW) Welding
SECTION 4:BASIC WELDING GUIDE
- 4.01 MIG (GMAW/FCAW) Basic Welding Technique
- 4.02 MIG (GMAW/FCAW) Welding Troubleshooting
- 4.03 Stick (MMAW) Basic Welding Technique
- 4.04 Stick (MMAW) Welding Troubleshooting
- 4.05 TIG (GTAW) Basic Welding Technique
- 4.06 TIG (GTAW) Welding Problems
SECTION 5:POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Power Source Problems
- 5.02 Routine Service and Calibration Requirements
- 5.03 Cleaning the Welding Power Source
- 5.04 Cleaning the Feed Rolls
SECTION 6:KEY SPARE PARTS
- 6.01 Power Source
- 6.02 Tweco Fusion 250 Mig Torch
APPENDIX: TRANSMIG 175i CIRCUIT DIAGRAM
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY – JULY 2010
WARRANTY SCHEDULE – JULY 2010
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 2: INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3: INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Transmig 175i Power Source Controls, Indicators and Features
- 3.07 Attaching the Tweco Professional Fusion Mig Torch (Euro)
- 3.08 Installing Minispool (100mm diameter)
- 3.09 Installing Handispool (200mm diameter)
- 3.10 Inserting Wire into the Wire Feed Mechanism
- 3.11 Feed Roller Pressure Adjustment
- 3.13 Wire Reel Brake
- 3.14 Shielding Gas Regulator Operating Instructions
- 3.15 Setup for MIG (GMAW) Welding with Gas Shielded Mig Wire
- 3.16 Setup for MIG (GMAW) Welding with Gasless Mig Wire
- 3.17 Setup for TIG (GTAW) Welding
- 3.18 Setup for Manual Arc (MMAW) Welding
SECTION 4: BASIC WELDING GUIDE
- 4.01 MIG (GMAW/FCAW) Basic Welding Technique
- 4.02 MIG (GMAW/FCAW) Welding Troubleshooting
- 4.03 Stick (MMAW) Basic Welding Technique
- 4.04 Stick (MMAW) Welding Troubleshooting
- 4.05 TIG (GTAW) Basic Welding Technique
- 4.06 TIG (GTAW) Welding Problems
SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Power Source Problems
- 5.02 Routine Service and Calibration Requirements
- 5.03 Cleaning the Welding Power Source
- 5.04 Cleaning the Feed Rolls
AP0-5143-APENDIX
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY - JULY 2010
WARRANTY SCHEDULE - JULY 2010
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION