Baseline Systems FreeWave Ethernet Radio User Manual
Fgr2-pe wireless data transceiver, For use with baseline irrigation controllers, User manual and reference guide
Advertising
Table of contents
Document Outline
- Chapter 1: Introduction
- Chapter 2: Setting Up and Programming Transceivers
- Basic Steps to Programming Plus-Style Transceivers
- Powering the Transceiver
- Determining and Setting a Transceiver's IP Address
- Resetting Transceivers to the Factory Default Settings
- Configuration Tool Options
- Reading Plus-Style Transceivers in Tool Suite
- Accessing Configuration Web Pages
- Navigating the Web Pages
- Providing Site Information
- Using the MultiPoint Gateway to Change All Connected Transceivers
- Creating User Logins
- Upgrading Plus-Style Transceiver Firmware Using TFTP Server
- Chapter 3: IP and Network Communication Settings
- Chapter 4: Serial Port Settings
- Setting a Serial Port's Mode
- Disabling Serial Ports
- Using the Serial Port as an Alarm Client
- Viewing a Serial Port's Status
- Serial Port Parameter Reference
- Alarm IP & Port
- Alarm Retry Limit (Attempts)
- Drop Link
- Multicast IP
- Multicast Port
- Serial Baud Rate
- Serial CD Mode
- Serial Data Bits
- Serial Flow Control
- Serial Interface
- Serial Modbus RTU
- Serial Parity
- Stop Bits
- TCP Client Enable
- TCP Client IP
- TCP Client Port
- TCP Server Enable
- TCP Server Inactivity Timeout
- TCP Server Port
- UDP Local IP Port
- UDP Power Up IP
- UDP Power Up Port
- UDP/Multicast Enable
- Utilize For Alarm
- Chapter 5: Radio Settings
- Radio Setup Parameter Reference
- Addressed Repeat
- Broadcast Repeat
- Broadcast Repeat in MultiPoint Networks with Repeaters
- Frequency Key
- Frequency Zones
- Network ID
- Master Tx Beacon
- Max Packet Size and Min Packet Size
- Modem Mode
- Network Type
- Repeaters
- Retry Timeout
- RF Data Rate
- Slave Attempts
- Slave Connect Odds
- Subnet ID
- Transmit Power
- Transmit Rate
- About the Call Book
- Radio Setup Parameter Reference
- Chapter 6: Security Settings
- Chapter 7: SNMP Settings
- SNMP Parameter Reference
- SNMP Trap Limit Parameter Reference
- Delta Alarm Enable
- Delta Alarm Below
- Min Fault Time
- Noise Alarm Above
- Noise Alarm Enable
- Rx Rate Alarm Below
- Rx Rate Alarm Enable
- Signal Alarm Below
- Signal Alarm Enable
- Tx Rate Alarm Below
- Tx Rate Alarm Enable
- VSWR Alarm Above
- VSWR Alarm Enable
- Voltage Alarm Above
- Voltage Alarm Below
- Voltage Alarm Enable
- Chapter 8: Viewing Transceiver Status and Statistics
- Refreshing and Resetting Statistics
- Available Statistics
- Bad Packets
- Broadcast Packets
- Connected To
- Disconnect Count
- Distance
- Firmware Version
- Hardware Version
- Noise
- Notes
- Packets Dropped
- Packets Sent
- Peer to Peer Packets
- Radio Addressed Packets
- Radio Parse Error
- Received
- Reflected Power
- RX Success Rate
- RX Throughput
- Signal
- Site Contact
- Site Name
- Software Boot Version
- System Name
- Temperature
- TX Success Rate
- TX Throughput
- Un-Acked Packets
- Upstream Noise
- Upstream Signal
- Uptime
- Voltage
- Wireless Version
- Chapter 9: Data Communication Link Examples
- Chapter 10: Additional Transceiver Information
- Appendix A: Firmware Updates
- Appendix B: Using the FreeWave TFTP Server
- Appendix C: Using the Discovery Server
- Adding Transceivers Manually to the Discovery Server List
- Deleting Transceivers from the Discovery Server List
- Changing Basic Settings Using Discovery Server
- Accessing a Transceiver's Web Page from Discovery Server
- Rebooting All Transceivers in the Discovery Server List
- Viewing Diagnostic Information in Discovery Server
- Working with Network Files in Discovery Server
- Exporting Transceiver Information from Discovery Server
- Upgrading Firmware from Discovery Server
- Appendix D: Changing the Computer IP Address in Windows
- Appendix E: Object Tree for FREEWAVE-TECHNOLOGIES-MIB
- Index